Motorola DCT3080 Installation Manual Download Page 51

Page: 51 / 98

DCT3080 Installation Manual

d02 Purchase Status

This diagnostic displays the status of subscriber event purchases on the
OSD and LED. The OSD and LED information displays are updated each
time this diagnostic is displayed:

PURCHASE STATUS

PURCHASES

UNSENT:

UNACK:

LAST SEQ NUM:

xxxx

LAST RB TIME:

xxxxxxxxxx

IPPV STATUS:

Enabled

Figure 3-3
LED display for PURCHASE STATUS diagnostic

MUTE

On when

enabled

IPPV

Number of unsent

purchases

Purchase indicator

The Purchase Status fields are:

Field Description

Unsent

The number of purchases in the DCT remaining to be polled. It can
be an integer from 0 to 63.

Unack

The number of reports that have not been acknowledged by the
controller. It is an integer.

Last Seq
Num

The last acknowledged sequence number of a purchase sent by the
controller. It is a 16-bit, unsigned hexadecimal number.

Last RB
Time

The last time the DCT3080 attempted to report back purchases to
the controller, in GPS seconds.

Summary of Contents for DCT3080



































































































Search results

Summary of Contents for DCT3080

Reviews:

Related manuals for DCT3080

Brands by name

Popular brands

Motorola DCT3080, Installation Manual

Search results

Summary of Contents for DCT3080

Reviews:

Related manuals for DCT3080

Brands by name

Popular brands