Motorola DCT3080 Installation Manual Download Page 71 | Manualshive

Page: 71 / 98

background image

DCT3080 Installation Manual

65

Field Description

HDMI Port

If a device is connected to the HDMI port

only

, the following

diagnostics display to help troubleshoot the HDMI interface.
They all display “N/A” if no device is connected to the HDMI
port or the value is invalid or cannot be retrieved.

Device
Connected

Indicates whether a device is connected to the HDMI port —
Yes or No.

Repeater

Indicates whether the connected device is a repeater —
Yes or No.

Video Xmission
(transmission)

Indicates whether the DCT3080 is transmitting video over the
HDMI port — Not Active or Active.

HDCP Enabled

Indicates whether the DCT3080 is using HDCP to encrypt
video transmitted over the HDMI link — Yes or No. If the
Video Xmission status is Not Active, the HDCP Enabled
status is No.

Video
Constrained

Indicates whether the DCT3080 is constraining the video sent
through HDMI — Yes or No. If the Video Xmission status is
Not Active, the Video Constrained status is No.

Output Format

Indicates the timing format of the video sent through HDMI:

1920 x 1080I — 1920 pixels wide by 1080 pixels high,
interlaced

1280 x 720P — 1280 pixels wide by 720 pixels high,
progressive

720 x 480P — 720 pixels wide by 480 pixels high,
progressive

720 x 480I — 720 pixels wide by 480 pixels high,
interlaced

640 x 480P — 640 pixels wide by 480 pixels high,
progressive

Aspect Ratio

Indicates the aspect ratio of the video sent through HDMI —
3:4 or 16:9.

«
...
69
70
71
72
73
...
»

Summary of Contents for DCT3080



































































































Reviews:

No comments

Related manuals for DCT3080

Brand: Yaesu Pages: 8

Brand: Pace Pages: 2

Brand: Q-See Pages: 19

Brand: Zepco Pages: 12

Brand: Hunt Electronic Pages: 57

Brand: Acard Pages: 48

Brand: Speco Pages: 110

Brand: Okina USA Pages: 11

Brand: COP-USA Pages: 66

Brand: Y3K Pages: 13

Brand: DGTEC Pages: 36

Brand: Advanced Technology Video Pages: 2

QuadraSplit 421SS

Brand: Advanced Technology Video Pages: 8

Brand: GRASS VALLEY Pages: 80

Ultimate Series

Brand: Ness Pages: 58

Brand: HIKVISION Pages: 20

Brand: HIKVISION Pages: 10

DV-7 HDRH-44-2U

Brand: DynDNS Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands