HIKVISION DS-2CE56D8T-IT3E User Manual Download

Page: 1 / 16

TURBO HD

D8T POC Series Bullet &

Turret Camera

User Manual

User Manual
Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:

Type

Model

Type I Camera

DS-2CE16D8T-IT1E

DS-2CE16D8T-IT3E

DS-2CE16D8T-IT5E

Type II Camera

DS-2CE16D8T-IT3ZE

Type III Camera

DS-2CE16D8T-ITE

Type IV Camera

DS-2CE56D8T-IT3ZE

Type V Camera

DS-2CE56D8T-IT1E

DS-2CE56D8T-IT3E

Type VI Camera

DS-2CE56D8T-ITME

This manual may contain several technical incorrect

places or printing errors, and the content is subject to
change without notice. The updates will be added to

the new version of this manual. We will readily improve

or update the products or procedures described in the
manual.

0100001081224

Summary of Contents for DS-2CE56D8T-IT3E

















Search results

Summary of Contents for DS-2CE56D8T-IT3E

Reviews:

Related manuals for DS-2CE56D8T-IT3E

Brands by name

Popular brands

HIKVISION DS-2CE56D8T-IT3E, User Manual

Search results

Summary of Contents for DS-2CE56D8T-IT3E

Reviews:

Related manuals for DS-2CE56D8T-IT3E

Brands by name

Popular brands