68009328001-A
December, 2009
Radio Alignment Procedures:
Transmitter Alignment Options
5-7
5.4.3.1 To Perform Transmit High Power Tuning, do the following:
1.
Under the
Tx Align
menu, select
Transmit Power
, then select
High
(
Figure 5-5
).
2.
Press
PTT Toggle
. This will key the radio up at 1st test frequency (F1).
3.
Adjust the high power level to be as defined by
Table 5-3
. Move the slider/spin control or keying in
values in the edit control (press
ENTER
to confirm your selection after typing in the softpot value).
4.
Press
PTT Toggle
to dekey the radio, go to the next frequency point by selecting the slider, typing
in the edit control box (press
ENTER
to confirm selection after typing in the softpot value) or
toggling the softpot value using the spin control.
5.
Press
PTT Toggle
again to key up the radio at the selected frequency point.
6.
Repeat steps 3-5 for the remaining test frequencies (F2-7)
7.
Press
Program
to store the softpot values into the radio’s codeplug.
8.
Exit the Transmit High Power function.
9.
If the radio uses only high power channels, proceed to adjust modulation. If low power channels
are used, perform Transmit Low Power Tuning as defined.
5.4.3.2 To Perform Transmit Low Power Tuning, do the following: -
1.
Under the
Tx Align
menu, select
Transmit Power
, and then select
Low
.
2.
Press
PTT Toggle
. This will key the radio up at 1st test frequency (F1).
3.
Adjust the power level to be as defined by
country power level specifications
by moving the
slider/spin control or keying in values in the edit control (press
ENTER
to confirm your selection
after typing in the softpot value).
4.
Press
PTT Toggle
to dekey the radio, go to the next frequency point by selecting the slider, typing
in the edit control box (press
ENTER
to confirm your selection) or toggling the softpot value using
the spin control.
5.
Press
PTT Toggle
again to key up the radio at the selected frequency point.
6.
Repeat steps 3-5 for the remaining test frequencies (F2-F7).
7.
Press
Program
to store the softpot values into the radio’s codeplug.
Table 5-3. Transmit High/Low Power Level
RF Band (MHz)
Model Number
High Power(W)
Low Power (W)
VHF 136-162 MHz
AAH50JDF9AA5AN
5.2-5.5
1.1-1.3
VHF 136-162 MHz
AAH50JDH9AA6AN
5.2-5.5
1.1-1.3
VHF 146-174 MHz
AAH50KDF9AA5AN
5.2-5.5
1.1-1.3
VHF 146-174 MHz
AAH50KDH9AA6AN
5.2-5.5
1.1-1.3
UHF 1 403-440 MHz
AAH50QDF9AA5AN
4.2-4.5
1.1-1.3
UHF 1 403-440 MHz
AAH50QDH9AA6AN
4.2-4.5
1.1-1.3
UHF 2 438-470 MHz
AAH50RDF9AA5AN
4.2-4.5
1.1-1.3
UHF 2 438-470 MHz
AAH50RDH9AA6AN
4.2-4.5
1.1-1.3
UHF 3 465-495 MHz
AAH50SDF9AA5AN
4.2-4.5
1.1-1.3
UHF 3 465-495 MHz
AAH50SDH9AA6AN
4.2-4.5
1.1-1.3
Summary of Contents for Commercial Series
