background image

1

introdduccion

1

1

important notes

Lay the parts out and compare to the PARTS CHECKLIST below. Do not discard and packaging until you are 

sure that you have all the parts.

This furniture is provided with an anti-topple device for securing to a wall. Failure to use this could result in the 

furniture toppling onto a child.

A Mothercare changing mat is recommended for use with this changing unit with maximum dimensions of 

82cm x 48cm. Place the mat evenly between the top rails.

   

1

introduction    introduccion

1

introduction    introduccion

1

introduction    introduccion

1

introduction    introduccion

1

introduction    introduccion

parts checklist

1

introduction    introduccion

2

parts checklist

1

introduction    introduccion

2

parts checklist

1

introduction    introduccion

2

parts checklist

1

introduction    introduccion

2

parts checklist

14 cross head screws 7 x 45mm 

61 dowels 

 

26 cam screws

 

8, 4 x 25mm domed head screws 

 

4 M6 x 14mm screws  

2 M6 x 36mm screws  

2 blanking screws

2 washers 

 

33, 3 x 16mm cross head screws 

26 cams 

1, 4 x 16mm cross head screws

4 handles 

 

 

 

5 back panel plates   

 

1 strap

2 back plates

1

Summary of Contents for little hampton changing unit













Reviews: