5
UK Helpline 0870 060 2614
Replacement Parts 0870 157 6645
Ireland Helpline 1800 409119
For details of other Morphy Richards products, please see our website:
2
Refilling can be done whilst the
appliance is in operation. It is
not necessary to wait for the
appliance to cool down.
3
Unlock the tank using the tank
release knob
„
. Slide out the
water tank and fill (see filling
instructions).
4
Alternatively, you can refill the
tank in ‘situ’ through the filler
‚
with the use of a measuring
jug or filling beaker.
STEAM IRONING
1
Connect the appliance to a
suitable mains outlet. Press the
power ‘ON’ button
Á
which
will glow red.
ALL MODELS
After a few minutes, the light
changes to green - indicating
the boiler is ready to generate
steam.
Check the iron temperature
indicator light
¤
has switched
off, indicating the iron is ready
to use.
MODELS WITH VARIABLE
STEAM
These models automatically
select the middle steam level
as the default setting.
To select a different steam
setting, press the steam button
Î
to select the desired steam
level.
2
Turn the temperature dial
›
on
the iron in a clockwise
direction, select dot-1, dot-2 or
dot-3 according to the
recommendation of the
garment label.
3
The iron’s temperature indicator
light
¤
goes off when the
required temperature is
reached.
4
Depress the steam button
⁄
for 1 minute to clear the system
of air (first time use only). This
will be accompanied by a
clicking noise which is quite
normal.
5
Begin first time ironing with an
old towel.
NOTE: If you press the steam
button before the steam
generator reaches its required
temperature, a warning double
beep will sound.
6
The appliance is ready to use.
7
Press the steam button
⁄
for
steam ironing.
8
Depress the power switch
Á
to turn off the base unit when
ironing is complete.
MODELS WITH
SPRAY FEATURE
Certain models are fitted with a
spray feature. Stubborn
creases and excessively dry
clothing can be softened by
damping the material with
water. This procedure means
ironing can be achieved without
applying excessive pressure.
Filling the spray
bottle
C
(certain models only)
To fill the spray bottle with
water, press the release button
Ô
and lift away the spray unit
Ì
.
Pull the bottle
away from
the spray unit in a downward
direction, taking care not to
damage the bottle, and fill
water to the ‘Full’ mark.
Re-assembly
C
Attach the bottle to the spray
unit, taking care to align the
parts correctly.
Locate the spray unit to the
front of the iron and press into
place until the unit locks into
position.
Press the pump
Ó
a few times
to purge the air from the
system, when a fine mist of
water is created, the unit is
ready for use.
DRY IRONING
1
Connect the appliance to a
suitable mains outlet.
2
Press the steam switch
Î
two
times until all three steam level
indicator lights go off (steam off
mode).
3
Turn the temperature dial
‡
on
the iron in a clockwise
direction, select dot-1, dot-2, or
dot-3 according to the
recommendation of the
garment label.
4
The temperature indicator light
¤
glows on the iron, indicating
that it is the correct setting for
the temperature.
5
When the required temperature
is reached, the temperature
indicator light on the iron goes
off. The iron is ready to use.
It is always a good idea to
begin with ‘cool’ fabrics and
work up to higher settings, as
an iron heats up quicker than it
cools down so you will save
time and electricity.
AUTO-SHUT OFF
(certain models only)
An auto-shut off system will
activate if the steam is not
used for over 15 minutes. The
mains indicator light
Á
will
flash between green and red,
indicating the unit is in ‘sleep
mode’.
When this occurs, press the
steam select button
Î
or the
power switch
Á
‘ON’ once.
The appliance will switch on
immediately and you need to
check, and select, the required
setting.
C
Ó Ô
Ì
RN42288MUK Rev8_Instruction Booklet 07/09/2011 13:56 Page 5
