10
11
12
Wards.com
1
•
888
•
557
•
3848
Wards.com
AC Removal
To remove air conditioner, turn power OFF and disconnect power cord. Remove the
5 screws installed in the top and bottom of the guide panels. Close guides and with
a firm grip on the unit tilt outward to allow any condensation to drain out.
To Store:
Be sure all parts are clean and dry before storing. Store appliance in original box.
Operating Instructions
(cont’d)
Operating Instructions
Control Panel:
Control Panel Functions:
Power - Use to turn AC ON and OFF.
CAUTION: After powering off the AC or switching from cooling to fan, wait a
minimum of 3 minutes before turning cooling back on.
Fan Speed - Use to set fan speed by pressing the button to desired selection:
Low > Medium > High > Low. A light will go on next to the selected speed.
Operation Mode - Use to switch between Cool > Energy Saver > Fan modes.
The corresponding light will illuminate with your selection.
• Cool mode - When the temperature of the unit is set colder than the air
temperature of the room, both the compressor and fan will run. But when
the room temp becomes colder than what is set on the AC, only the fan
will run.
• Energy Saver mode - At a set temperature, when the compressor stops
the fan will automatically turn off. When the compressor turns on again,
the fan will turn on.
• Fan mode - The control panel displays the room temperature and only
the fan will run, not the compressor.
Temperature Buttons - Use the up arrow to increase and down arrow to decrease
the temperature, which is displayed on the control panel. Every press of the but-
ton will increase or decrease the temperature by 1˚ F. The range of settings is
88˚ F to 61˚ F. Temperature controls only work in cooling mode.
Timer Set - Use this button to designate the number of hours (up to 24) the unit
should run continuously until automatically shutting down
or the number of hours
until the unit automatically starts. Each press of the button increases the time,
which is displayed on the control panel, by 1 hour. When the display reaches 24,
pressing the Timer Set button again will cancel the timer.
To set number of hours for continuous operation, press Timer Set when the AC is
ON. The display on the control panel will show the number of hours for 10 sec-
onds and then display the set temperature. However, if in fan mode the tempera-
ture displayed will be that of the room.
To set the number of hours until the unit automatically powers up, press the Timer
Set when the AC is OFF.
Air Flow Direction - Use the wheel on the front of the unit to adjust the louvers to
direct air flow to the left, right or straight ahead.
To use the remote control, you must be within 20 feet of the unit with a clear line of
sight. Remove batteries when control is not in use for long periods of time.
Sleep Mode:
The AC must be in Cool Mode prior to using the Sleep Mode. When the Sleep Mode
has been activated, the temperature set in the unit will increase 2˚ F one hour after
Sleep Mode has been turned on and will increase another 2˚ F one hour after that.
During Sleep Mode, the Fan Speed will automatically switch to LOW.
Error Codes:
If the display on the control panel shows E1 or CF, it’s time to clean the filter.
If the display shows ER, EN or ED, call for service.
Increase Temperature
Only works in Cool Mode. Press-
ing and holding will increase temp
1˚ F every 0.6 seconds with range
being 61˚ F - 88˚ F.
Decrease Temperature
Only works in Cool Mode. Press-
ing and holding will decrease
temp 1˚ F every 0.6 seconds with
range being 61˚ F - 88˚ F.
Operation Mode
Press to select Cool > Fan > Cool
High Speed
Indicator Lamp
Medium Speed
Indicator Lamp
Low Speed
Indicator Lamp
Fan Speed
Button
Temperature Increase
Button
Timer Indicator Lamp
Timer Set
Button
Cool Mode
Indicator Lamp
Fan Mode
Indicator Lamp
Energy Saver
Indicator Lamp
Operation Mode
Button
Temperature Decrease
Button
On / Off
Button
