18
19
MANAGING NETWORK SETUP
At the network level, there are four operations the remote can perform: Network Reset, Network
Recovery, Network Update, and Remove Fail Node.
Network Reset
Network Reset deletes all nodes from the network, restoring the network to its original state
before the first node was ever added. Be sure to follow this step beforeyou create a network.
To perform a Network Reset:
If you’re not already at the Home screen, press the
1.
button to move back one screen
at a time until the only two choices appearing are Monster and Add Device.
Use the
2.
or
button to highlight Monster.
Press and hold the
3.
key
shift
button for 3 seconds. The menu changes and Nodes is highlighted.
Use the
4.
or
button to highlight Network (an eighth menu choice not displayed among
the first three) and press the
button.
Use the
5.
or
button to highlight Reset (if it is not already highlighted by default)
and press the
button.
The green LED under the
key
shift
button blinks rapidly while this command is in progress.
If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL
or EMPTY (to specify the network contains zero nodes).
Note:
Once you complete a Network Reset, if you want to add a Z-Wave module or reprogram
one, make sure to perform a hard resent on each module or device you want to add or reprogram.
Network Recovery - Re-optimizing the Z Wave RF Signal routing for optimized performance
of the Z wave Network
Network Recovery rebuilds all routines for all the nodes in the network. To perform a Network
Recovery:
If you’re not already at the Home screen, press the
1.
button to move back one screen
at a time until the only two choices appearing are Monster and Add Device.
Use the
2.
or
button to highlight Monster.
Press and hold the
3.
key
shift
button for 3 seconds. The menu changes and Nodes is highlighted.
Use the
4.
or
button to highlight Network (an eighth menu choice not displayed among
the first three) and press the
button.
Use the
5.
or
button to highlight Recovery and press the
button.
The green LED under the
key
shift
button blinks rapidly while this command is in progress.
If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL
or EMPTY (to specify the network has zero nodes).
Network Update
Network Update ____ all nodes on the network. To perform a Network Update:
If you’re not already at the Home screen, press the
1.
button to move back one screen
at a time until the only two choices appearing are Monster and Add Device.
Use the
2.
or
button to highlight Monster.
Press and hold the
3.
key
shift
button for 3 seconds. The menu changes and Nodes is highlighted.
Use the
4.
or
button to highlight Network (an eighth menu choice not displayed among
the first three) and press the
button.
Use the
5.
or
button to highlight Update and press the
button.
The green LED under the
key
shift
button blinks rapidly while this command is in progress.
If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL
or EMPTY (to specify the network has zero nodes).
Remove Failed Node
Remove Failed Node removes any node not found when the remote sends signals to all nodes
on the network. To perform a Removed Failed Node:
If you’re not already at the Home screen, press the
1.
button to move back one screen
at a time until the only two choices appearing are Monster and Add Device.
Use the
2.
or
button to highlight Monster.
Press and hold the
3.
key
shift
button for 3 seconds. The menu changes and Nodes is highlighted.
Use the
4.
or
button to highlight Network (an eighth menu choice not displayed among
the first three) and press the
button.
Use the
5.
or
button to highlight Remove Failed Nodes (a fourth menu choice not
displayed among the first three) and press the
button.
The green LED under the
key
shift
button blinks rapidly while this command is in progress.
If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL
or EMPTY (to specify the network has zero nodes).
