Monoprice Blackbird 31057 User Manual Download | Manualshive

Page: 7 / 16

background image

7

5.

AUDIO IN: 3.5mm stereo analog jack for connecting the audio output of the VGA
video source device.

6.

IR OUT: 3.5mm jack for connecting an IR transmitter (not included).

7.

RS232: 3-pin Euroblock connector for connecting a computer for RS-232 control.

8.

AUDIO OUT: 3-pin Euroblock connector for connecting a speaker.

9.

DC 12V: DC barrel connector for connecting the included AC power adapter.

SAMPLE CONNECTION DIAGRAM

«
...
5
6
7
8
9
...
»

Summary of Contents for Blackbird 31057

















Reviews:

No comments

Related manuals for Blackbird 31057

Brand: Magnetrol Pages: 24

Brand: Xenteq Pages: 22

Brand: LevelOne Pages: 17

Brand: P-Link Computer Pages: 92

Brand: I-Tech Pages: 29

Brand: cable matters Pages: 12

Brand: X-keys Pages: 4

Brand: senva Pages: 2

Brand: socomec Pages: 38

Brand: Cypress Pages: 4

Brand: Kramer Pages: 35

Brand: Anker Pages: 16

Brand: Nortel Pages: 46

ControlZAPP CZ CEFL 10VDC

Brand: DANLERS Pages: 2

FlexFabric 12900

Brand: HPE Pages: 118

Brand: D-Link Pages: 11

Brand: D-Link Pages: 37

Brand: D-Link Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands