Monoprice 24179 User Manual Download | Manualshive

Page: 32 / 35

background image

32

4.

Download the .zip file containing the firmware upgrade file.

5.

Extract the .zip file to get the .dfu firmware upgrade file.

6.

Using a micro USB cable (not included), plug one end into one of your PC's USB
ports, then plug the other end into the FIRMWARE port on the front panel.

7.

Using the included IR remote control, put the matrix into Standby mode.

8.

While pressing and holding the INPUT 2 and INPUT 3 buttons, use the remote
control to power the matrix on. The Power LED will begin flashing red, indicating
that the matrix is in firmware upgrade mode. If it does not, put the matrix back into
standby mode and try again.

9.

Double-click the DfuSe Demonstration icon to launch the firmware upgrade
program.

«
...
30
31
32
33
34
...
»

Summary of Contents for 24179




































Reviews:

No comments

Related manuals for 24179

Brand: Hama Pages: 5

SuperStack 3 4900

Brand: 3Com Pages: 2

Brand: Radial Engineering Pages: 12

Brand: DANLERS Pages: 2

QuantaMesh T1048-LB9

Brand: QCT Pages: 42

Brand: SMC Networks Pages: 43

Brand: Gembird Pages: 2

Sierra Pro XL 1608V5S

Brand: Kramer Pages: 2

Brand: Ruby Tech Pages: 254

Brand: Lindy Pages: 4

Brand: ATEN Pages: 4

Brand: Edge-Core Pages: 65

Brand: UNIARCH Pages: 6

Brand: IPGARD Pages: 15

Brand: Airlinkplus Pages: 2

Brand: Hored Pages: 4

Grid Director 4700

Brand: Mellanox Technologies Pages: 88

Brand: Radio Shack Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands