background image

25 

5.

 

If the LED display shows EE91, refer to the EXX1, EEXX, and EX9X lines. 

6.

 

If the suggested fix does not work, try turning the vacuum off, wait 30 seconds, 
then turn it back on again. 

7.

 

Note that, because of the drop sensing feature, the vacuum will not properly 
sense the floor when placed on dark surfaces and that the obstacle sensors 
cannot properly sense the location of dark walls. The vacuum cannot be used on 
dark surfaces. 

 

TECHNICAL SUPPORT 

Monoprice is pleased to provide free, live, online technical support to assist you with 
any questions you may have about installation, setup, troubleshooting, or product 
recommendations. If you ever need assistance with your new product, please come 
online to talk to one of our friendly and knowledgeable Tech Support Associates. 
Technical support is available through the online chat button on our website 
www.monoprice.com during regular business hours, 7 days a week. You can also get 
assistance through email by sending a message to [email protected] 
 

SPECIFICATIONS 

Model 

16385 

Dust Bin Capacity 

16.9 fl. oz. (0.5 liters) 

Battery Type 

2000mAh Ni-mh 

Battery Voltage 

14.4 VDC 

Charging Time 

About 4 ~ 6 hours 

Cleaning Time 

Up to 100 minutes 

Dimensions 

ø13.4" x 3.3" (ø340 x 85 mm) 

Weight 

7.5 lbs. (3.4 kg) 

 
 

 

Summary of Contents for 16385




























Reviews: