background image

INTRODUCTION 

Thank you for purchasing this Intelligent Robot Vacuum! This vacuum can automatically 
clean the floor of almost any room. It features several cleaning modes, including 
Normal, Spot, and Edge cleaning. It uses side brushes and powerful suction to clean the 
floor without agitator brushes. It can clean for up to 100 minutes at full power on a 
single charge and can automatically return to its Charging Station when the battery 
charge is low. It has a large dust bin and HEPA filter, and includes a remote control. 
 

FEATURES 

 

Normal, Spot, and Edge cleaning modes 

 

Cleaning can be scheduled 

 

Powerful suction to clean even the smallest dirt or dust 

 

Can clean carpeted and non-carpeted floors 

 

Automatically adjusts suction power based on floor type 

 

Washable dust bin and main filter 

 

Includes infrared remote control 

 

PACKAGE CONTENTS 

Please take an inventory of the package contents to ensure you have all the items listed 
below. If anything is missing or damaged, please contact Monoprice Customer Service 
for a replacement. 

 

1x Vacuum 

 

1x Charging Station 

 

1x Power Adapter 

 

1x Remote Control 

 

2x HEPA Filters 

 

1x Cleaning Brush 

 

4x Side Brushes 

 

1x User's Manual 

Summary of Contents for 16385




























Reviews: