Monogram ZIF360NHLH Installation Instructions Manual Download Page 37 | Manualshive

Page: 37 / 52

background image

Installation Instructions - Flush Installation

STEP 10 CONNECT WATER SUPPLY

(FREEZER MODELS ONLY)

• Locate and bring the tubing to the front of the cabinet.
• Turn the water on to flush debris from the line. Run

about a quart of water through the tubing into a
bucket, then shut off the water.

Copper Tubing:
• Slip a 1/4” nut and ferrule (provided) over both ends of

the copper tubing. Insert the tube into the union fitting
on the unit and tighten the nut to the union.

• Turn on the water to check for leaks.
GE SmartConnect

™

Tubing:

NOTE: The only GE-approved plastic tubing is supplied
in the GE SmartConnect

™

Refrigerator Tubing kits. Do

not use any other plastic water supply line because the
line is under pressure at all times. Other types of plastic
may crack or rupture with age and cause water dam-
age to your home.
• Insert the molded end of the tubing into the appliance

or freezer connection. Tighten the compression nut
until it is just hand-tight.

• Tighten one additional turn with a wrench.

Overtightening can cause leaks!

• Turn on the water to check for leaks.
NOTE: Make sure excess tubing length does not
interfere with the toekick installation.

Freezer

Water Supply

House

Water Supply

STEP 11 START ICEMAKER

(FREEZER MODELS ONLY)

• Slide the switch to ON. The icemaker will begin

operation automatically.

• Be sure nothing interferes with the sweep of the feeler

arm.

• Discard the first full bucket of ice cubes.
• To turn the icemaker off, slide the switch to OFF.

Icemaker

Feeler Arm

Power

Switch

STEP 12 INSTALL TOEKICK

• Locate the supplied toekicks (shipped taped to the

side of the refrigerator.

• The wider set of toe kicks will be used for flush

installation. You can discard the other set of toe kicks.

• Install the toekick assembly with the 2 screws provid-

ed, adjust to the desired height and tighten screws.

IMPORTANT: A custom toekick can be installed to
match or complement the surrounding cabinetry but
can NOT cover the horizontal vent slots of the factory
toe kick”

37

«
...
35
36
37
38
39
...
»

Summary of Contents for ZIF360NHLH





















































Reviews:

No comments

Related manuals for ZIF360NHLH

Brand: Selecta Pages: 24

QUIET-COOL CLS-COOL1

Brand: Middle Atlantic Products Pages: 8

Brand: Blomberg Pages: 22

Brand: Hamilton Beach Pages: 28

Brand: Haier Pages: 1

Brand: Vissani Pages: 28

Brand: SCAN domestic Pages: 33

Brand: Amica Pages: 32

NOVAMATIC SO1840-IB

Brand: FUST Pages: 60

Brand: WC Wood Pages: 1

Brand: Zanussi Electrolux Pages: 20

Brand: VALERA Pages: 2

Brand: Magic Chef Pages: 30

Brand: Sovereign Pages: 13

8LCH-KK-SC-SSF-40

Brand: Glacial Pages: 27

Brand: Omcan Pages: 16

Brand: Candy Pages: 127

Brand: Panasonic Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands