background image

Installation Instructions - Flush Installation

32

 STEP 4  INSTALL CASE TRIM

The unit arrives with case trim for standard installation 

attached. Flush installation case trim is provided. Remove 

the factory installed case trim. Install new case trim using 

supplied right hand and left hand case trim pieces and 

case trim screws. Attach case trim to each side of case 

as shown in illustration using case trim screws in holes 

provided down each side of the case.

• The kit supplied with the unit contains 2 lag bolts and 4 

toggles with bolts. The wall bracket will be attached to 
the wall in 4 places.

• Measure the opening where the unit is to be installed. 

Mark the center with a vertical line.

• Measure up 82” from the floor. Mark this point on the 

wall.

• Using a level, draw a horizontal line on the wall at this 

height.

• Locate at least 2 studs on the back wall. Mark these 

points on the horizontal line.

• Place the bottom of the wall bracket with tabs on the 

horizontal line. Align the center notch on the bracket 
with the center line on the wall.

• The anti-tip wall bracket has a series of holes. Select 2 

holes that match with the located studs. Make sure the 
holes selected are on the center of the studs. Mark the 
wall at these points.

 STEP 5   INSTALL ANTI-TIP BRACKET 

(cont.)

Two Additional 

Hole Locations at 

Ends of Brackets

Center

Wall Bracket

Line On Wall

Wall Studs

82”

To Floor

WARNING

 

 Tip Over Hazard. 

The unit is top-heavy and must be secured to prevent the 
possibility of tipping forward.

AVERTISSEMENT

 

 Risque de basculement  

L’appareil ménager est beaucoup plus lourd en haut et il 
faut le maintenir en place pour éviter la possibilité de son 
basculement vers l’avant.

• Cut a 1” x 4” block, 35” long. 
• Measure and mark under the soffit, 

5-1/4” from the front edge of the 
cabinet. 

• Secure the wood block to under the 

soffit. From the bottom of the block 
to the finished floor should measure 
84”. See the illustration.

 STEP 5  INSTALL ANTI-TIP BRACKET

Summary of Contents for ZIF360NHLH





















































Reviews: