background image

6

Moto Alarm System

Hazard warning lights

This is a hazard light warning feature for motorcycles even if they do not have a hazardwarning switch.
Pressing both the 

GREY and BLACK buttons 

of the remote control for 

3 seconds 

when the ignition is OFF and

the alarm system is armed will start the 

hazard warning lights

.

NOTE

: If the motorcycle battery voltage is too low to maintain this feature, the lights will flash 5 times and then

stop.

To turn off the hazards either press both buttons again for 3 seconds (leaves the system armed) or press the

GREY 

button to disarm the alarm system and turn off the hazard lights.

NOTE

: For safety reasons the hazard light feature cannot be used with the ignition turned on.

Press and hold GREY and BLACK at the same time

‘Panic/locator’ feature

Press and hold the 

BLACK button

 of the remote for 

3 seconds 

with the ignition switched OFF to enter 

‘panic/

locator’

 mode.

The siren will sound and the indicators will flash until any button is pressed on the remote control to turn the panic/

locator mode off.

When triggered, the alarm system reverts to the original state held before the button was pressed to activate the

panic/locate mode.

Press and hold BLACK button for three seconds

Winter mode

The purpose of this mode is to enable you to leave the machine for long periods of time with the alarm drawing an

absolute minimum current (250

µ

A) from the machine’s battery. In this mode the alarm system is no longer active and

it leaves the machine immobilized only.

Should you decide to place the machine in this state, we strongly advise you to use further measures to protect

your machine with quality physical security.

NOTE

: The machine’s battery will still naturally discharge over time so we advise you to check its condition

periodically.

РУ

ССКИЙ

27

Охранная  система  для  мотоциклов

Пример ввода PIN кода для снятия сигнализации с охраны

Включить зажигание и
оставить его включенным

Через 30 секунд тревога

прекратится и светодиод

загорится на 5 секунд

В течение 3 секунд

светодиод мигает

быстрыми вспышка'

ми

В течение 3 секунд

светодиод мигает

быстрыми

вспышками

Не позднее чем через
5 секунд выключите и

включите  зажигание

Режим тревоги

30  секунд

Ввод 1 цифры

1 звуковой сигнал/

вспышка

Выключить зажигание

Ввод 2 цифры

включить зажигание

4 звуковых сигнала/

вспышки

Выключить зажигание

Ввод 3 цифры

включить зажигание

2 звуковых сигнала/

вспышки

Выключить зажигание

Ввод 4 цифры

включить зажигание

6 звуковых сигнала/

вспышки

Выключить зажигание

Если PIN код введен правильно, индикатор'

ные фонари мигнут один раз, и сигнализация

снимется с охраны

Не позднее чем через 45 секунд включите зажигание

Summary of Contents for PENTACLE M-1































Reviews: