background image

14

Moto Alarm System

How to remove your machine’s battery

You can remove the battery at any time when the system is in the ‘

immobilised only

’ or in ‘

winter mode

’.

Winter mode also stops the remotes operating the system making this setting better.

If the alarm system has been armed, the internal battery backup system is also turned on and disconnection of

the battery will cause the alarm system to sound.

If you have changed the standard default setting of the alarm to full passive arming the easiest way to remove the

machine’s battery is to select ‘winter mode’ prior to removal of the battery.

Special features (Dealer selectable only)

The following features can only be accessed by your dealer. Should you wish to have a setting changed from the

factory default please discuss this with your dealer first. The factory default settings have been chosen to deliver the
optimum performance from the system.

The factory default settings are in bold text.

NOTE

: The inclusion of arm and disarm indication beeps is strictly forbidden in all EU countries.

Press GREY button

Ignition

ON

Ignition

OFF

Press both buttons for
10 seconds until beep

Disconnect

battery

РУССКИЙ

19

Охранная  система  для  мотоциклов

Дистанционная постановка на охрану

Для включения режима полной охраны с включением всех датчиков, входов концевых выключателей и

подключением встроенного автономного питания используйте дистанционную постановку на охрану. Для ди
станционной постановки на охрану нажмите не позднее чем через 45 секунд после выключения зажигания

серую кнопку

 пульта дистанционного управления. Индикаторные фонари мигнут дважды, через 5 секунд

начнет мигать светодиод, и включится режим полной охраны.

Примечание 1: С помощью функции №6 в таблице установочного программирования можно включить

звуковые сигналы подтверждения постановки на охрану.

Примечание 2: Если Вы программно включили переход системы в режим полной охраны (функции №2 в

таблице пользовательского программирования) при автоматической постановке на охрану, то режим полной
охраны будет включаться как после дистанционной, так и после автоматической постановки. Если же после
автоматической постановки задан режим иммобилайзера, то для постановки сигнализации в режим полной
охраны после автоматической постановки нажмите серую кнопку дважды: первый раз для отключения иммо
билайзера и второй раз – для постановки на охрану.

Примечание 3:  При постановке в охрану система запоминает положение основного и дополнительного

концевых выключателей, тревога включается при изменении их состояния.

Постановка на охрану с отключенными датчиками (режим транспортировки)

Для постановки сигнализации на охрану с отключенными датчиками наклона и удара нажмите черную

кнопку не позднее чем через 10 секунд после нажатия серой кнопки. Индикаторные фонари мигнут дважды,
подтверждая постановку на охрану, а затем еще три раза, сообщая о том, датчики отключены. При охране с
отключенными датчиками сигнализации попрежнему контролирует включение зажигание, концевые выклю
чатели и прерывание питания.

Примечание: Постановка на охрану с отключенными датчиками возможна только с пульта управления. При

автоматической постановке на охрану отключить датчики описанным выше способом нельзя.

Две вспышки фонарей. Свето
диод горит 5 секунд, затем на
чинает мигать, включается ре
жим полной охраны.

Нажать для поста
новки на охрану

Две вспышки фонарей

Нажать для поста
новки на охрану

Три вспышки фонарей

Нажать не позднее,
чем через 10 се
кунд

Summary of Contents for PENTACLE M-1































Reviews: