background image

20308636

25

AVFLST Vent Free Fireplace

TOUCH SCREEN REMOTE CONTROL OPERATION

2.  When the current setting is B), pressing TIMER button 

and THERMO button at the same time for 3 seconds 

will switch to A) Mode. The touch area icons will disap

-

pear.

n

 

Safety Features

1.  Low Battery Detection
  When  low  battery  condition  occurs,  the  trans

-

mitter will turn off the fireplace.
A) Battery voltage is checked every one minute. 

When the battery voltage is low, the LCD dis

-

plays a low battery icon which will exist in all modes.

B) The  transmitter  will  not  operate  with  low  battery 

voltage. Change the batteries before the batteries 

become too weak for normal operations.

2.  Power On Initialization
  After the power-on initialization, the transmitter sends 

a signal to turn off the fireplace.

3.  Thermal Shutdown
  When the ambient temperature is more than 99°F, the 

transmitter will turn off the fireplace.
A) The LCD will display “HI.”
B) The Transmitter will not function until 

the  room  temperature  has  dropped 

below 99 degree Fahrenheit.

4.  Low Temperature Condition
  When  the  ambient  temperature  is  less  than  40  de

-

grees  Fahrenheit,  the  LCD  will  display 

“LO,”  and  NO  SIGNAL  will  be  sent  to 

turn on the appliance.

  All  functions  still  remain  the  same  for 

both  Manual  Mode  and  Thermostat 

Mode.

5.  Child-proof Protection
  The child-proof icon will be shown when 

the  child-proof  mode  is  activated  by 

pressing  the  ON  button  and  the  OFF 

button  at  the  same  time  for  three  sec

-

onds.
A) Enter childproof mode by pressing and holding both 

the ON button and the OFF button simultaneous

-

ly  for  3  seconds.  The  Childproof  indicator  will  be 

shown on the LCD.

B) Deactivate childproof mode by pressing and hold

-

ing the ON button and the OFF button simultane

-

ously for 3 seconds again. The Childproof indicator 

disappears on the LCD.

C) The  transmitter  cannot  be  operated  in  childproof 

mode.

n

 

Using the Mounting Base

The transmitter comes with a mounting base which allows 

you to hang the transmitter on the wall.
1.  Secure the mounting base 

on  the  wall  with  supplied 

screws.  For  best  viewing 

angle,  make  it  the  same 

height as your eyes.

2.  Hang  the  transmitter  on 

the  hook  of  the  mounting 

base,  then  push  down  so 

the  transmitter  is  flush  to 

the mounting base.

FP2674
mounting base

FP2612
low battery

FP2613
HI

FP2614
lo no child

Figure 29. 

 

Summary of Contents for AVFLST42NTSC









































Reviews: