Monessen Hearth AVFLST42NTSC, Installation & Operating Instructions Manual

Page: 22 / 40

22
20308636
AVFLST Vent Free Fireplace
TOUCH SCREEN REMOTE CONTROL OPERATION
Resetting the transmitter
If the transmitter is not working properly, reinstall the bat -
teries to reset the transmitter.
1. Pull out at least one of the batteries.
2. Press any key on the screen to discharge.
3. Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds
until the display refreshes will also reset the transmitter.
n
Functions and Operations
General:
The TSFSC Remote Control has four (4) operating
modes: Manual, Timer, Thermostatic and Smart Mode.
The control system can be set to temperature range be -
tween 45° F and 90° F. The flame height can be adjusted
in the manual, timer and thermostatic mode. The Smart
Mode will automatically adjust flame height according to
the difference between Set and Room temperatures.
The transmitter will operate the remote receiver from 1
foot to a maximum of 30 feet. The distance is reduced
when batteries are low.
Manual Mode
Figure 23
In this mode, the TIMER button and the THERMO but
-
ton will only display “TIMER” and “THERMO,” respec -
tively without showing the time and the SET temperature.
Pressing the ON/up and OFF/down buttons will change
the flame height if none of the menu buttons (TIMER,
THERMO, LIGHT, AUX) are pressed and flashing.
1. Press the ON/up button to turn on the fireplace. The
flame icon on the LCD displays High.
WARNING!
Do not use two (2) or more remote control systems
in the same area with the same privacy code set-
ting, as they will communicate with each other.
This may cause the appliances to malfunction.
Setting Privacy Code on Transmitter:
Figure 20
The remote transmitter privacy code
is preset in factory. In the event of
activation or interference from other
nearby transmissions, change the
code using the following procedures
(learn function must be performed af -
ter changing the code):
1. Press the ON/arrow button and
the TIMER button at the same
time to enter privacy code setup
models.
2. The setup display is shown in the
figure. The four digits on the top
stand for the privacy code. The default values of the
four digits will be all “0.”
3. The first digit will be flashing upon entering the setup
mode. Push the ON button to toggle its value between
“0" and “9,” and push the “OFF” button to jump to the
next digit. The next digit will then start flashing and the
first one stops flashing. Set up the four digits to your
choice between “0" and “9.”
4. After setting up all the four digits, push “OFF” to finish
the process and return to the previous mode.
5. The Signature Command
®
control board then needs to
re-learn the new setting.
Performing Learn Function
1. The RF receiver button on the control board in the
fireplace must be in the on position before the learn
function can begin. Figure 21 With the Command Cen -
ter master switch in the ON position, use paper clip to
depress the recessed button on Control Board, one
beep for RF receiver ON or two beeps for RF receiver
OFF.
2. Holding the OFF button on the Command Center while
turning on the master switch will activate the learn
function for the transmitter.
3. After the above oper -
ation, two beeps will
sound and the green
LED on the Command
Center will flash for 10
seconds.
4. During the 10 sec -
onds, press the OFF
button on the trans -
mitter to learn. Anoth -
er two beeps will be
sound confirming a
successful learn func -
tion.
FP2649
set privace code
Figure 20.
FP2650
command ctr ctrl brd
Battery Door
Master Switch
ON
LED
OFF
FP2650
Front Panel Bezel
(Optional)
FP2650
command ctr ctrl brd
RF Receiver
ON/OFF
Figure 21.
Figure 22. Command Center