background image

This is an unvented gas-fired heater. It uses air 

(oxygen) from the room in which it is installed. 

Provisions for adequate combustion and 

ventilation air must be provided. Refer to 

Page 7.

20308636  0516  Rev. 1

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

•  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

•  WHAT TO DO IF YOU SMELL GAS

  – Do not try to light any appliance.

  – Do not touch any electrical switch; do 

not use any phone in your building.

  – Leave the building immediately.

  – Immediately call your gas supplier from 

a neighbor's phone. Follow the gas 

supplier's instructions.

  – If you cannot reach your gas supplier, 

call the fire department.

•  Installation and service must be performed 

by a qualified installer, service agency or 

the gas supplier.

  WARNING! If the information in this manual 

is not followed exactly, a fire or explosion may 

result causing property damage, personal 

injury or loss of life.

AVFLST Vent Free See Through

 

Fireplace System

 

Installation & Operating Instructions

Models: 

AVFLST42NTSC and AVFLST42PTSC

Summary of Contents for AVFLST42NTSC









































Reviews: