Molift Quick Raiser 2+ Technical Manual Download Page 3

Page 3 of 24

General advice

This technical manual contains important informa-
tion about the lifter, including safety instructions. 
It is therefore essential to read it carefully before 
using and repairing the patient lifter.

Explanation of symbols

Locations  in  diagrams  are  referred  as  follows: 

A

1

 

A1 refers to Appendix A, position 1. 

  This symbol appears in the user manual next 

to all the information which concerns safety 
in the work-place and the risk of injury. Always 
follow these instructions carefully, paying due 
attention and caution. 

  This symbol indicates important information 

regarding  the  correct  use  of  the  equipment 
as described in this technical manual. If this 
information  is  not  taken  into  account,  mal-
function  or  damage  to  the  equipment  may 
result.

  This  symbol  draws  your  attention  to  especi-

ally useful information, which could help the 
user  of  this  equipment  to  work  more  effici-
ently. This information may simplify procedu-
res or clarify complications.

Safety regulations

Heavy, long and/or sharp objects will have to be 
lifted and handled when repairing the lifter. When 
assembling and removing parts, the lifter’s stabi-
lity may be affected with the risk of it overturning 
or falling over.

You  are  therefore  advised  to  be  attentive  and 
careful!

Liability

Please  read  these  operating  instructions  care-
fully  before  putting  the  product  into  opera-
tion.  We  assume  no  liability  for  damage  or  mal-
functions  resulting  from  failure  to  comply  with 
the  instructions.  Warranty  claims  must  be  made 
immediately on detecting the defect. Remember 
to quote the serial number. Consumable parts are 
not subject to the warranty.

All  technical  information,  data  and  instructions 
for  operation  contained  in  these  operating 
instructions were up-to-date at time of print and 
are compiled on the basis of our experience and 
to the best of our knowledge. We reserve the right 
to  incorporate  technical  modifications  within 
the scope of further development of the product 
described in this manual. No claims can be derived 
from the information, illustrations or descriptions 
contained in these instructions. We assume no lia-
bility  for  any  damage  or  malfunction  caused  by 
operating errors, non-compliance with these ope-
rating instructions or inappropriate maintenance. 
We  expressly  point  out  that  only  genuine  Molift 
Group  AS  spare  parts  and  accessories  approved 
by us may be used.  For safety reasons, the fitting 
and use of spare parts or accessories, which have 
not  been  approved,  and  unauthorised  modifi-
cation or conversion of the product, are not per-
mitted. Molift Group AS will accept no liability for 
damages resulting from such acts.

With the exclusion of product liability, Molift Group 
AS is liable for faults or omissions on its part within 
the scope of the warranty obligations stated in the 
purchase contract. Claims for damages are exclu-
ded,  irrespective  of  the  legal  reason  from  which 
such  claims  are  derived.  Only  documentation 
belonging to the actual equipment is valid.

Any failure to comply with the safety regulations 
and precautionary measures stated in these ope-
rating instructions renders the declaration of con-
formity  supplied  with  the  system  in  accordance 
with  Council  Directive  (93/42/EEC)  concerning 
medical devices invalid.

Summary of Contents for Quick Raiser 2+

























Reviews: