Page 9 of 32
Make sure the brake is properly greased.
• Place the hexagon lock nut and tighten by
hand.
Check the contact points between chas-
sis and column are clean and movable
before mounting the column.
• Mount the column on the chassis and per-
form a function test of the column.
• Mount the top cap with screws.
• Mount the lifting arm with suspension
• Test the lifter according to the safety control
test
Changing parts in chassis
The legs should be in middle position
when dismounting to have best possible
access.
• Remove the column with lifting arm from
chassis and put it aside on a safe place.
• Place the chassis on a working stand.
Removing the leg spreading motor
• Loosen the leg spreading motor (4) from the
swiwel joint (2) by removing the screw (3)
and nut (1).
You need an external power source to
run the leg spreading motor out of the nut
spindle.
Take care that no fingers are crushed
when moving the leg spreading mecha-
nism.
• Disconnect the cable contact on the leg
spreading motor (push and pull), and attatch
the external power.
• Run the leg spreading motor in until the
spindle is free from the nut holder.
NOTE! Be careful not to run legs in end po-
sition.
• Remove the motor and disconnect the exter-
nal power.
• If necessary the bracket (9), the nut holder
(11) with nut spindle (4) can be changed by
removing the screws (18). Use heat to re-
move the screws.
H
Bill of materials:
1
Material.
Comment.
Dimension/
Draw. no.
Description.
Qty.
Pos.
13-177 BOM.xls
C
G
13
14
15
5
7
6
17
9
4
11
Add loctite 2701
12
18
22
21
22
Add loctite 2701
Add loctite 2701
Add loctite 2701
15
F
G
Add grease on spindle, Mobilith SHC 007
19
20
23
24
25
26
See assembly procedure no. 13-P02
H
Added info regarding Loctite
13.10.2009 RVS
MHL
G
Replaced pos 20, added pos 26.
15.10.2008/TES
TES
F
Added assembly procedure no.
08.05.2008
MHL
E
Updated pos ballons and BOM list
15.01.2008
MHL
D
Updated labels
15.11.2007
TÅB
C
Added labels and changed ingoing
screw
25.10.2007
MHL
A
Released for production
23.03.2007
T.B.
Rev.
Description:
Date/Sign.
Approved:
59
4
ISO 7380 - M8 x 12 ---
12C
58
1
Art. and id no.
13-216
57
1
Only authorized
personell label
13-218
56
1
Rubber spindle
13-175
55
2
DIN 7991 - M8 x 12 --
- 3.8N
54
1
Bushing,
Ø14/Ø12X5
03-320
53
2
Nut holder 1/2 part 13-133
52
4
Torp no.
17W12504
Washer DIN 125 - A
17
51
1
Bracket
13-135
50
2
Locking plate
13-030
49
1
Bolt
13-025
48
2
Bolt for leg
13-026
47
1
Nut spindle
13-021
46
1
Flat bar right leg 2 13-173
45
2
AV 02711 00824 1410118
44
2
1320110
43
4
A020000X0
42
4
A020000X
41
4
A01_000X
40
4
STOPFEN
39
4
0910180
38
1
Flat bar left leg 2 13-179
37
4
Distance ring
13-029
36
2
Shock cap w/
wheel bracket
13-116
35
2
13-183
34
2
13-117
33
2
Leg profile
machined2
13-174
32
2
Washer DIN 125 - A
10.5
31
1
1320133
30
1
1320132
29
1
Washer DIN 9021 - 6.4
28
1
Hexagon Nut ISO 4032
- M6 - W - N
27
2
Washer Ø10.5
DIN 6340 350 HV
Washer_Ø10,5_
DIN6340
26
1
Socket Head Cap
Screw_DIN
25
1
DIN 914 - M4 x 8-N
24
1
Cable
13-062
23
3
Cable
13-062
22
1
Cable
13-062
21
1
Distance ring
13-049
20
1
DIN 912 M6 x 40 ---
24N
19
1
Avstandshylse_12 X
2.9 X 12
18
2
ISO 10642 - M10 x 50
--- 50N
17
6
0220118
16
5
Cable shoe round
15
4
Probe lower
mould
13-057
14
1
Lower mould
contact
13-059
13
2
03-104
12
1
0220111
11
2
ISO 10642 - M10 x 45
--- 45N
10
2
1320127 O-ring ø12x5
NBR70
9
1
Axle
13-035
8
1
Sviwel joint
13-023
7
1
Eccentric lock
chassie
13-126
6
1
Motor Valeo
404689
(m/snekkeskrue) 1320150
5
1
1220110
4
2
003_000X
3
2
008_000X
2
2
007_000C
1
1
Chassie mould
13-142
Pos.
Qty.
Description
Dimension/
Draw. no.
Material:
Comment:
Molift Partner 255
Drawing name:
15.12.2005
Drawing number:
Chassie w/legs assy 2
A2
13-177
1:5
RVS
Projection:
Scale:
Date:
Designed/Drawn:
Size
• The swiwel joint can be removed by turn-
ing it counterclockwise until it falls down and
out off position. Pull the swiwel joint care-
fully out. (The swiwel joint is supported by a
flange in the back when it is in position).
1
2
3
4
