background image

Inspection On Arrival

1.  Inspect unit upon arrival. In case of damage, report 

immediately to transportation company and your local 

Modine sales representative.

2.  Check rating plate on unit and motor to verify that power 

supply and motor specification requirements meet available 

electric power at the point of installation.

3.  Inspect unit received for conformance with description of 

product ordered (including specifications where applicable).

THIS MANUAL IS THE PROPERTY OF THE OWNER. 

PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB.

General Information

Installation and wiring of these electric unit heaters must conform 

to all applicable local codes and the National Electric Code. 

Wiring of these electric unit heaters should only be performed by 

a qualified electrician.
These electric unit heaters are Listed by Underwriters 

Laboratories, Inc. Representative samples of this product 

have been evaluated by UL and meet the applicable U.S. and 

Canadian safety standards with components as furnished.
All replacement parts and controls are proprietary in that they 

have all been designed, tested, and approved for the particular 

application to insure both physical fit and electrical performance. 

Any substitution of parts or controls not approved by Modine will 

be at installer’s risk. For replacement parts, submit the unit  

heater model number, power code, control code and serial 

number shown on the rating plate attached to the unit.
Do not remove outlet fan guard from vertical electric unit heaters 

except to service the unit.

 

Contents

General Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation

 

Special Precautions / Important Instructions. . . . . . . . . .2

 

Unit Locations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

 

Ceiling Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

 

Wall Mounting Bracket  . . . . . . . . . . . . . . . . . . . . . . . . . .5

 

Dimensional/Performance Data  . . . . . . . . . . . . . . . . . . .6

  

Motor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

  

Wiring Instructions/Data  . . . . . . . . . . . . . . . . . . . . . . . 7-8

Operation

 

Prior to Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

 

Initial Start-up  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Model PTE

Model VE

INSTALLATION AND SERVICE MANUAL

electric unit heaters

models VE and PTE

2-506.14

5H605869 

January, 2013

WARNING

IMPORTANT

The use of this manual is specifically intended 

for a qualified installation and service agency. 

A qualified installation and service agency 

must perform all installation and service of 

these appliances.

FOR YOUR SAFETY

The use and storage of gasoline or other 

flammable vapors and liquids in open containers 

in the vicinity of this appliance is hazardous.

Improper installation, adjustment, alteration, 

service or maintenance can cause property 

damage, injury or death, and could cause 

exposure to substances which have been 

determined by various state agencies to cause 

cancer, birth defects or other reproductive 

harm. Read the installation, operating and 

maintenance instructions thoroughly before 

installing or servicing this equipment.

Summary of Contents for PTE













Reviews: