Modine Manufacturing HDS Installation And Service Manual Download Page 15

15

SERVICE / MAINTENANCE / TROUBLESHOOTING

Serial Number Designations 

(Remove access cover to locate)

01 01 101 01 05 1000

MOTOR 
SUPPLIER CODE

01- Century
05- Universal
etc.

YEAR OF
MANUFACTURE

05- 2005
06- 2006
etc.

WEEK OF
MANUFACTURE

01-  1st week of year
26-  26th week of year.

SEQUENCE 
NUMBER

FAN SUPPLIER 
CODE

01- Revcor
08- Brookside
etc.

SERIES IDENTITY NUMBER

Identifies which series of controls 
were furnished on the unit.

Model Number Designations 

(Remove access cover to locate)

HDS - Low 

Profile Separated 

Combustion

MBH INPUT

30 - 30,000 Btu/hr input
45 - 45,000 Btu/hr input
60 - 60,000 Btu/hr input
75 - 75,000 Btu/hr input

HEAT EXCHANGER TYPE

A - Aluminized

H - Hot surface ignition

CONTROL CODE 
TYPE

34

 - 115V/25V single 

stage hot surface ignition, 
100% shut-off with 
lockout - natural gas.

74

 - 115V/25V single 

stage hot surface ignition, 
100% shut-off with 
lockout - propane gas.

POWER CODE

01 -  

115 volt, 60 hertz, 

single phase

H D S   4 5   A   H   0 1   3 4

Replacement Parts

When requesting parts please contact your local representative. Please have full model and serial number available. If you require 
assistance in locating your representative, please call the number located on the back page.

MODINE MANUFACTURING COMPANY

LIMITED WARRANTY

(Residential Use Only)

WHAT THIS WARRANTY COVERS

This warranty covers all defects in material and workmanship in your 
Modine unit heater, when used for your home or garage.

WHAT THIS WARRANTY DOES NOT COVER

Unit heater, or any of its parts:

1.  which have been improperly installed or removed.

2.  which have been damaged other than by normal use.

3.  which have not been properly maintained.

4.  which have been exposed to gas input more than 5% higher than 

specified on the serial plate of the unit heater, resulting in over-firing of 
the heater.

5.  which have been exposed to possibly corrosive chemicals or chemical 

vapors (such as found in swimming pools), or potentially explosive or 
flammable atmospheres laden with grain dust, sawdust, or similar air-
borne materials.

6.  where any defect has been caused by abuse, misuse, neglect, 

carelessness, or accident.

7.  where the serial number of the unit heater has been altered, defaced, 

or removed.

8.  which are used in a confined space without adequate combustion air, 

such as can be found in more air-tight construction.

WHO THIS WARRANTY COVERS

This warranty covers the purchaser of the unit heater or anyone else who 
owns it during the warranty period.

HOW LONG THE WARRANTY LASTS

1.  The warranty for the heat exchanger of the unit heater remains in force 

for ten years from the date you purchased the unit heater.

2.  The warranty on all other parts of the heater remains in force for two 

years from the date you purchased the unit heater.

WHAT MODINE WILL DO TO CORRECT ANY WARRANTY DEFECTS, 
AND HOW YOU CAN GET WARRANTY SERVICE

In the event of warranty failure, Modine will provide replacement parts 
at Modine's cost. To obtain warranty repairs or replacement of defective 
parts, you must, within the period of warranty coverage, contact the agency 
from whom you purchased the unit heater. That seller, or the service 
agency performing service for the seller, will determine whether or not 
the unit heater, or any of its parts, is in fact defective, and will then either 
repair or obtain and install the necessary replacement parts for you. If it 
is determined that the unit heater or parts were not defective, you may be 
charged for any replacement parts.

CAUTION - Do not attempt to repair the unit heater yourself, nor remove it 
or any of its parts. This must be done by a qualified service agency.

If you have any questions about this warranty, call the person from 
whom you purchased the unit heater; or a Modine Heating Products 
Representative at 1-800-828-4328.

WHAT MODINE WILL NOT DO

Modine will not reimburse you for any labor costs or service charges 
related to warranty repairs or replacements.

INCIDENTAL AND CONSEQUENTIAL DAMAGES DISCLAIMED

This warranty does not cover incidental damages, such as use of substitute 
heating equipment, or other costs arising from the loss of use of the unit 
heater. This warranty also does not cover consequential damages, such as 
the cost of repairing or replacing other property which is damaged when 
this unit heater does not work properly.

HOW STATE LAW RELATES TO THIS WARRANTY

Some states do not allow the exclusion or limitation of incidental or 
consequential damages so the above limitations or exclusions may not 
apply to you.

This warranty gives you specific legal rights, and you may also have other 
rights which vary from state to state.

Figure 15.1
Common Replacement Parts 

 

30

  3H36919 5H79402 5H75001 5H75002-3  5H75029 5H79441-1 

5H78126-1 5H75032 5H76382  5H76383

 

45

  3H36920 5H79402 5H75001 5H75002-3  5H75029 5H79441-2 

5H78126-1 5H75032 5H76382  5H76383

 

60

  3H36921 5H79402 5H75769 5H75002-3  5H75029 5H79441-3 

5H78126-1 5H75032 5H76382  5H76383

 

75

  3H36922 5H79402 5H75769 5H75002-3  5H75029 5H79441-3 

5H78126-1 5H75032 5H76382  5H76383

Model 

Size

Heat 

Exch. Kit

Limit 

Control 

Switch

Flame 

Roll-out 

Switch

Transformer

Pressure 

Switch

Combination Gas

Igniter

Ignition 

Control

Control 

Code 74

Control 

Code 34

 

The above list is subject to change.  Please refer to unit mounted parts list for most up-to-date list.

Power 

Exhauster

Summary of Contents for HDS

































Reviews: