6
Transportation & Storage:
During transportation, the machine should be carefully handled and do not put it upside down to prevent from
damaging to the shell and inside. The appliance should be stored in a ventilated room without corrosive gas. If it
needs to be stored in open air temporarily, make sure to stay dry.
Notice for Installment:
1.
All the installation of this device should be done by professional and qualified personnel.
2.
The connection shall comply with the regulations of gas safety, installation and use.
3.
The installament has to be taken carefully because the appliance is heavy. It is recommended to mount it on
the floor.
4.
The appliance should be placed in a flat area and kept a minimum distance of 10cm away from the objects on
both sides and 20cm at the back (e.g. walls, windows, etc). Do not mount it on flammable surface.
5.
The appliance should be located in a well ventilated place with air exhaust facilities to ensure that the steam
and burned gases can be discharged during operation.
6.
The mounted appliance shall be secured, lying horizontally, with no tilting or shaking when using.
7.
The user shall apply for the permission of the gas supplier for using such gas type prior to the installation of
the appliance. Only install it after verification that the supplied gas is same as the gas to be used in the future
Gas Connection:
1.
Use neither gases which are not applicable for this device nor any high or middle pressure regulation valves.
(it is only applicable for low pressure regulation valve).
2.
Before installing the device, there shall mount a quick -acting gas cut off valve, which shall also be at the
upstream near the device and ready accessible.
3.
Ensure that the connected gas type is the same as the rated gas type of the device, if not, do not use it.
4.
The conduit which is connected to the device shall be connected by metal pipe.
5.
If the conduit pressure is higher or lower than the required pressure of the device of 10%, there shall install a
regulator to ensure the rated pressure.
6.
After connecting, test the tightness of the joint with a solution of water and soap or detecting instrument.
Do
not check it with open flame.
Special note
1.
The installation, initial start up and maintenance of this device shall be done by professional personnel or
installation personnel have been approved by manufacturer.
2.
Remove the package, make sure that the device is intact. If there’s any doubt, please do not use it and
consult to professional. Keep away the packaging from children (the material is plastic bags, nails and so on).
3.
When use this appliance for the first time, the ignition time may be a little longer due to the air in the newly
installed
. If it doesn’t ignite at the first time, turn off the ignition switch and re-ignite it after 3 minutes’ interval
to avoid deflagration.
4.
When stop using, the appliance must be turned off.
5.
This is a commercial appliance which is not applicable for home use. All the operation shall be done by trained
& professional personnel.
6.
It is only intended for commercial use, otherwise it would be dangerous.
7.
Do not disassamble or modify the device, serious accidents may happen when disassembling or modifying.
8.
Do not pat the appliance or put any heavy objects onto it. Irregular operation may cause damage and danger.
9.
Do not store any substances at the smoke vent of the gas heater to prevent obstruction of the discharge of
fumes that can cause hazardous to personal health.
10. High temperature may cause scald. Do not touc h the appliance directly with hand due to high temperature
during or after the operation.
11. Do not destroy the control panel with hard or sharp objects.
12. Do not wash it with spraying water. Wash the stainless steel surface appropriately and regularly to prote ct
against damages done by surface oxidation or chemical action.
Part 2: Installation
Summary of Contents for CT 7320G
Page 1: ...User Manual Book Burner CT 7960G CT7640G CT7320G CT 7660G ...
Page 4: ...4 Part 1 Name of Parts ...
Page 10: ...11 20 ...