Page 6
Page 35
Before you begin assembly, group the parts as we list them below. This will ensure that you have all of the parts before you begin assembly
and it will also help you become familiar with each part.
q
(1) Fuselage
q
(1) Right Wing Panel with Aileron and Flap
q
(1) Left Wing Panel with Aileron and Flap
q
(1) Horizontal Stabiliser with Elevator Halves
q
(1) Vertical Stabiliser with Rudder
q
(1) Main Landing Gear Bracket
q
(2) Main Gear Wheels
q
(2) M4 x 35mm Machine Screws
q
(6) M4 Flat Washers
q
(4) M4 Lock Nuts
q
(3) M3 x 16mm Machine Screws
q
(3) M3 Flat Washers
KiT CoNTeNTS
AirFrAMe ASSeMblieS
MAiN lANDiNG GeAr ASSeMbly
q
(2) Wheel Covers
q
(2) Wire Struts
q
(2) Bungee Covers
q
(2) Bungee Cover Mounts
q
(2) Rubber Bands
q
(6) M2 x 6mm Wood Screws
q
(8) M2 Flat Washers
q
(8) M2 Hex Nuts
MAiN lANDiNG GeAr ACCeSSorieS
q
(1) Prebent Tail Wheel Wire
q
(1) Tail Wheel
q
(1) Nylon Tail Wheel Mounting Bracket
q
(1) Nylon Steering Arm
q
(1) Nylon Spacer
q
(3) M3 x 12mm Wood Screws
q
(1) M2 x 10mm Wood Screw
q
(2) Wheel Collars
q
(2) M3 x 6mm Machine Screws
TAil Wheel ASSeMbly
iF yoU Find any parts missing or damaged, please contact yoUr local model tech
dealer directly, Using the separate cUstomer service sheet inclUded with yoUr kit.
q
(1) 14-1/2" (368mm) Pushrod Wire with Z-Bend
q
(1) Adjustable Pushrod Connector with Nut and Machine Screw
ThroTTle CoNTrol SySTeM
q
Align the two holes in the wing strut with the two holes in the wing, then
secure the wing strut to the wing, using two M3 x 10mm machine screws and
two M3 flat washers.
q
Repeat the previous procedures to install the second wing strut on the other half of the aircraft.
q
# 1 Phillips Head Screwdriver
q
Modeling Knife
q
Scissors
q
Electric Drill
q
1/16" (1.6mm) & 5/64" (2mm) Drill Bits
q
Straight Edge Ruler
q
Pencil
q
(1) Battery Tray (for Electric Version)
q
(1) Decal Set
q
Airplane Stand
q
Masking Tape
q
Heat-Shrink Tubing (for Electric Version)
q
Heat Gun (for Electric Version)
q
Soldering Iron (for Electric Version)
q
Solder (for Electric Version)
FiNAl ASSeMbly
you'll NeeD The FolloWiNG PArTS FroM The KiT:
you'll NeeD The FolloWiNG ToolS AND SuPPlieS:
STeP 1: InSTAllIng The ReCeIveR, BATTeRy AnD SWITCh hARneSS - glOW veRSIOn
q
Install the switch into the switch mount and use a scrap length of wire,
attached to the switch and passed through the fuselage side, to turn the switch
on and off.
q
After you've found the final location of the receiver and the battery, mount
them into the fuselage using your favorite method. We mounted the receiver
battery under the fuel tank and mounted the receiver to the fuselage floor in
front of the servos.
q
Make a receiver antenna wire mount out of an extra servo horn.
q
Drill a 5/64" (2mm) hole through the bottom of the fuselage, then run the
receiver antenna wire out along the bottom of the fuselage and secure it to the
tail wheel wire, using a rubber band and the antenna mount that you made.
IMPORTANT
This step details the installation of the receiver, battery and switch harness if you're using a glow engine. If you're
using a brushless electric motor, please skip to steps 2 and 3 on page 36.
q
Wrap the receiver and battery in foam rubber to protect them from vibration. Use a couple strips of masking tape or rubber bands to
hold the foam rubber in place.
+
Do not wrap the foam rubber too tightly or the vibration dampening quality will be reduced.
IMPORTANT
After tightening the two wing strut mounting screws in the wing, tighten the wing strut mounting screw in the fuselage.
Servo
Horn
Cut
Antenna
To Tail Wheel Wire
Modified Servo Arm
Rubber Band
Remove This
Portion