Page 16
Page 25
q
# 1 and # 2 Phillips Head Screwdrivers
q
Electric Drill
q
5/64" (2mm) Drill Bit
q
(1) Prebent Tail Wheel Wire
q
(1) Tail Wheel
q
(1) Nylon Tail Wheel Mounting Bracket
q
(1) Nylon Steering Arm
q
(1) Nylon Spacer
q
(3) M3 x 12mm Wood Screws
q
(1) M2 x 10mm Wood Screw
q
(2) Wheel Collars
q
(2) M3 x 6mm Machine Screws
q
Straight Edge Ruler
q
Pencil
q
Rotary Tool with Cutting Disc
TAil Wheel iNSTAllATioN
you'll NeeD The FolloWiNG PArTS FroM The KiT:
you'll NeeD The FolloWiNG ToolS AND SuPPlieS:
STeP 1: ASSeMbliNG The TAil Wheel brACKeT
q
Push one wheel collar into the top of the steering arm, making sure that the threaded hole in the wheel collar lines up with the hole
in the side of the steering arm, then partially thread one M3 x 6mm machine screw into the wheel collar.
q
Push the tail wheel wire up through the tail wheel mounting bracket, then
slide the steering arm over the tail wheel wire and push it down against the
mounting bracket.
q
Rotate both the tail wheel wire and the steering arm so that they face the
back of the mounting bracket. While holding the two in alignment, tighten the
machine screw, then
cut the end of the tail wheel wire off flush with the top of
the steering arm.
STeP 2: iNSTAlliNG The TAil Wheel ASSeMbly
q
Place the tail wheel mounting bracket onto the fuselage, making sure that
the mounting bracket is centred and that the steering arm pivot point is even
with the rudder hinge line.
q
When satisfied with the alignment, mark the locations of the three mounting
screws onto the fuselage.
q
Drill three 5/64" (2mm) diameter pilot holes through the fuselage, then install
the tail wheel mounting bracket, using three M3 x 12mm wood screws.
q
Push the steering arm mounting tabs over the bottom of the rudder.
q
Thread the M2 x 10mm wood screw into one side of the steering arm
mounting bracket, through the rudder and into the other side of the steering
arm mounting bracket, to secure the steering arm to the rudder.
q
Slide the adjustable pushrod connector assembly onto the pushrod wire,
then install the servo horn onto the servo, making sure that the servo horn is
angled approximately 30 degrees from centre.
q
While holding the carburetor fully closed, install and tighten the machine
screw in the top of the adjustable pushrod connector.
q
Cut away the excess pushrod wire, then install and tighten the servo horn retaining screw to hold the servo horn securely to the servo.
q
Open and close the throttle several times to ensure that the carburetor opens and closes completely and without binding. You may
need to adjust your transmitter EPA settings to achieve perfect settings.
q
# 2 Phillips Head Screwdriver
q
Modeling Knife
q
Scissors
q
(1) 320cc Fuel Tank
q
(3) Aluminium Tubes
q
(1) Rubber Stopper
q
(1) Metal Plate - Small
q
(1) Metal Plate - Large
q
(1) Fuel Pick-up (Clunk)
q
(1) Silicone Fuel Tubing
q
(1) Metal Support Ring
q
(1) M3 x 20mm Machine Screw
q
Straight Edge Ruler
q
Pencil
q
220 Grit Sandpaper
Fuel TANK iNSTAllATioN - GloW VerSioN
you'll NeeD The FolloWiNG PArTS FroM The KiT:
you'll NeeD The FolloWiNG ToolS AND SuPPlieS:
STeP 1: ASSeMbliNG The rubber SToPPer
q
Slide the large diameter metal plate over the tubes at the front of the rubber
stopper, and slide the small diameter metal plate over the tubes at the rear of
the rubber stopper.
q
Measure the distance that the two aluminium tubes protrude from the front
of the stopper assembly. This distance should be 3/8" (10mm).
IMPORTANT
Discard the shortest aluminium tube. It will not be used if you're using an in-cowl fueling valve as suggested. If you
don't use an in-cowl fueling valve, use the shortest aluminium tube as the fill tube.
q
Carefully bend the longer of the two aluminium tubes up at a shallow angle,
being careful not to kink the tubing as you bend it.
IMPORTANT
When the stopper assembly is installed in the fuel tank, the
top of the vent tube should rest just inside the moulded bubble in the top
of the fuel tank.
q
Use 220 grit sandpaper to lightly sand away any burrs that might be on the ends of the two aluminium tubes.
q
Push the two aluminium tubes through the rubber stopper.