Model Tech Super Cub ARF Assembly Instructions Manual Download Page 1

Page 40

Page 1

Fold along dotted line

Fold along dotted line

Global Hobby Distributors

Attn: Global Services

18480 Bandilier Circle

Fountain Valley CA  92728-8610

Post Office 

will not deliver 

without proper 

postage

                                
                                
                                

(Return Address Here)

Kit Product Number  MT3178D-1

Check out our website for more information on other exciting Model Tech products!

hTTP://MoDelTeCh.GlobAlhobby.CoM

Made in China

FeATureS

ASSEMBLY INSTRUCTIONS

Wing Span:  

81 Inches (2057mm)

  

l

 

 Wing Area:

  900 Square Inches (58.1dm

2

)  

l

 

 

length:

  50.75 Inches (1289mm)

Weight rTF:

  6.5-7.5 Pounds (2.9-3.4kg)  

l

 

Wing loading:

  17-19 Ounces/Square Foot (52-58gr/dm

2

)

Functions:

  Ailerons, Elevator, Rudder, Flaps and Throttle  

l

  

engine required (Glow Version):

  .46 - .61 Two-Stroke or .52 - .70 Four-Stroke

Power System required (electric Version):  

4120/05 Brushless Outrunner / 80 Amp Brushless ESC / 4 Cell 4000mAH LiPO

Completely Prebuilt and Covered with Iron-On Covering Material

Accepts Glow Power and Brushless Electric Power Systems

Stable, Predictable Flight Characteristics

Fiberglass Cowling and Aluminium Landing Gear Bracket

Clear Moulded Windshield and Side Windows

Complete Hardware Set - Wheels, Pushrods, Fuel Tank, Clevises, Etc.

l

 

Fast and Easy Assembly - Over 100 High-Resolution Photos to Guide You

SPeCiFiCATioNS

Model Tech Co., Ltd.

Hong Kong

© 2008, Model Tech Co., Ltd.

All Rights Reserved

Version 1 January 2008

Summary of Contents for Super Cub ARF





















Reviews: