background image

MODE supports multi disc games two different ways:

1.  You can place all games image files in one folder and MODE will 
intelligently queue them up together during game play.

2.  Or you can leave multi disc games in separate folders and on the MODE 
menu, press and hold the A button to bring up the contextual menu.

From here you can select “Add disc to queue”. You will see at the top of the menu “Discs in queue: X”. Do this for each game disc and afterwards press and hold 
the A button one more time and select Launch Current Queue to play the multi disc game. 

You can clear all discs in the queue by selecting Clear Disc Queue 

from the contextual menu.

Dreamcast disc changing is accomplished by 

using three possible options:

1.  When prompted to change a disc hit SW2 button on the MODE board itself.
2.  Use DCDigital’s on screen display option to change disc (see advanced install below).
3.  Wire a button to the Switch 1 pin on the JST9 connector to be used externally or in a tray mount.

Saturn disc changing is accomplished by opening and closing the disc lid upon prompt.

Multi Disc Games

Changing Discs on a Multi Disc Game

Summary of Contents for Terraonion


































Reviews: