background image

22

/40

 Mx2wire User Manual:

  InSTALLATIOn

 

© MOBOTIX AG  •  Security-Vision-Systems  •  Made in Germany

  www.mobotix.com  •  [email protected] 

Preparing The Standard Flush-Mounted Socket

In general, the existing fl ush-mounted socket of the two-wire cable continues to be used 
for Mx2wire. Otherwise, a fl ush-mounted socket must be fi tted fi rst. Make sure that the 
socket you use is as fl ush with the wall as possible, so that you can install the respective 
Mx2wire unit properly. Make sure that the socket and Mx2wire unit are aligned correctly 
in the wall. 

After

 connecting the two-wire cable, there are 

two ways

 to attach the Mx2wire circuit 

board to the fl ush-mounted socket:

1.  Secure the 

Mx2wire

 housing and circuit board 

directly to the socket

 by fastening 

two small screws (item 1.4) in the 12 o'clock and 6 o'clock positions. However, this 
requires that the socket is properly aligned in the wall. Thanks to the elongated shape 
of the screw holes, it is possible to make small adjustments to the left and to the 
right when tightening the screws.

  

2.  Use four or two (diagonally opposite one another) Torx screws/screw anchors 

(item 1.6) to tightly screw the 

Mx2wire

 housing and circuit board 

to the wall

. We 

recommend this procedure if the installed fl ush-mounted socket is not properly 
aligned or is not fl ush with the wall. Otherwise, the Mx2wire unit could easily be 
pulled out together with the fl ush-mounted socket.       

Two screws, diagonally opposite one another, are normally suffi  cient.

caution

Do not drill through live cables in the wall.

Attached to the socket 

using two screws

(item 1.4) 

Attached to the wall 

using two or four Torx 

screws/screw anchors 
(item 1.6)   

Summary of Contents for Mx2wire









































Reviews: