background image

11 

4.3

 

CONFIGURATION AND SYNCHRONISATION 

The  device  settings  can  be  programmed  in  the  Mobeye  Internet  Portal.  In 
this way you prepare the settings, to be picked up by the device. Since the 
Mobeye device is leading in the communication between the portal and the 
device, the data synchronisation is done after:  
1)

 

any  message  to  the  portal  (e.g.  the  regular  test  message,  alarm,  low 
batteries). 

2)

 

reconnecting power and reinserting batteries. 

3)

 

pressing the button (at the backside) for 5 seconds. 

4)

 

pressing  the  SYNC  symbol  in  the  portal  settings  (only  visible  if  external 
power  is  connected),  or  sending  the  SMS  command  1111  SYNC  to  the 
phone number in the unit (1111 is the security code in factory settings). 

 

During the data exchange with the portal, the LED flashes green. A battery-
operated unit will first blink red-green while connecting to the network. 

4.4

 

BASICS OF THE MOBEYE INTERNET PORTAL 

Dashboard 

With  multiple  devices,  the  dashboard  shows  all  devices,  with  the  (alarm) 
messages in the last 24 hours, (missed) test messages and low battery status.

 

If devices in the dashboard have logging functions, the dashboard changes 
when you click on "Diagrams" or "Gauges" in the gray bar. 
Select a device to go to the details of a specific device. 

 

Status & History 

The status block shows values about the status of the unit. 
If the "Synchronised" status is set to "No", there are new  settings or  alarm 
numbers that still need to be transferred to the device. 
The  network  strength  value  at  the  last  communication  session  is  shown.  If 
the value is lower than -98 dB, consider another location for the device. 
Click on the position icon 

 

to see the geographical location during the last 

report. Note: this is an indication based on "cell-id". 
 
The history displays all historical events. Click on "all events" to see the list. 

 
 

Summary of Contents for PowerGuard CM4100

































Reviews: