background image

• Isolate the mains supply to the fitting
• Remove the capping nut, and using plyers pull out the protective insert from the fitting 
  (see Fig. 4)

• Align the pins on the sensor, push onto the fitting, and tighten ensuring a good seal is 
   made. Do not overtighten
• The rotation and tilt of both sensors can be adjusted once fitted. For the PIR accessory, 
   please ensure it is positioned with the adjustment dials at the bottom
• With the LUX set to Daytime, and the TIME set to the minimum, perform a walk test to 
   set the SENS setting so the required detection area is covered. Then set the TIME and 
   LUX controls to the desired settings:

PIR / MICROWAVE SENSOR ACCESSORY

 

Fig. 4 

 

Align the pins on the sensor, push onto the fitting, and tighten ensuring a good seal is made. Do not 

overtighten 

 

The rotation and tilt of both sensors can be adjusted once fitted. For the PIR accessory, please ensure 

it is positioned with the adjustment dials at the bottom 

 

With the LUX set to Daytime, and the TIME set to the minimum, perform a walk test to set the SENS 

setting so the required detection area is covered. Then set the TIME and LUX controls to the desired 

settings: 

Setting 

FLNMIC 

FLNPIR 

SENS 

Minimum: up to 4m 

Maximum: up to 12m 

Minimum: up to 5m 

Maximum: up to 10m 

LUX 

Minimum: 3 lux 

Maximum: 2000 lux 

Minimum: 10 lux 

Maximum: 2000 lux 

TIME 

Minimum: 10 sec 

Maximum: 15 min 

Minimum: 10 sec 

Maximum: 7 min 

 

Override Function (FLNPIR only) 

 

Switch the mains supply to the fitting OFF-ON-OFF-ON within three seconds. The light flashes ON-

OFF-ON to indicate that it is in override mode. To return to automatic mode, switch the mains supply to 

the fitting off for at least 10 seconds, then switch on again 

 

The FLNMIC has no override function 

WARNING 

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 

testing. Irreparable damage will occur if this instruction is not followed. 

GENERAL 

The LED lamps fitted in this product are non-replaceable. The product should be recycled in the correct manner 

when it reaches the end of its life. Check local authorities for where facilities exist. 

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not 

use aggressive cleaning products or solvents which may damage the product.   

Do not use any source of high-pressure washers to maintain or clean this luminaire. 

This product is non-dimmable. 

WARRANTY

 

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with 

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will 

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of 

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation 

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve 

the right to alter product specification without prior notice. 

 

Fig. 4

Summary of Contents for FLN10









Reviews: