manualshive.com logo in svg

MK Diamond Products MK-101-24HD, Owner'S Manual & Operating Instructions

Share
Download
MK Diamond Products MK-101-24HD Owner'S Manual & Operating Instructions Download Page 45

45

MK-101-24HD   

TROUBLESHOOTING

Blade Stops Turning

(A)  

Allow motor to cool and de-

press motor Overload Reset 

Switch

(B)  

Verify all plugs fully installed. 

Check Ground Fault Circuit 

Interrupter

Verify circuit breaker at least 20 amps - if not, move to 20-amp circuit.

Verify circuit breaker not tripped. If tripped, reset once.

Check power source voltage is 120V - if not 120V, move to another circuit.

NOTE: 

If alignment problems are the result of a warped blade, a bent frame or bent support 

arm, or, if alignment  is off by more than 1/8-inch, contact the MK Diamond Service 

Center – (800) 474-5594     

(A)

Combination square (square) 

12-inch or greater. 1/2-inch 

Wrench or MK Triple Hole Box 

Wrench and MK Open  

End Wrench.

Blade Alignment Procedure

Tools Needed

The Movable Cutting Table of the MK-101-24HD may become misaligned with the Cutting Head of the 

Tile Saw over  time.  Should misalignment occur, perform the following steps to realign the Tile Saw.  

NOTE: 

Summary of Contents for MK-101-24HD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands