manualshive.com logo in svg

MK Diamond Products MK-101-24HD, Owner'S Manual & Operating Instructions

Share
Download
MK Diamond Products MK-101-24HD Owner'S Manual & Operating Instructions Download Page 23

23

1.   The MK-101-24HD weighs approximately ninety-eight (98) pounds.

2.   Never transport the MK-101-24HD with water in the Water Basin.

CAUTION

The MK-101-24HD is designed with a rigid frame and removable Cutting Head. Two people are re-

quired to transport the MK-101-24HD with the Cutting Head installed. Remove the Cutting Head if one 

person is transporting the saw (see Cutting Head Installation and Removal in the following section).

TRANSPORT

Lift Point

Lift Point

Cutting Head

The MK-101-24HD weighs approximately ninety-eight (98) pounds; follow the 

guidelines for transport in the TRANSPORT section, when placing it on the 

stand.

CAUTION

StanD (Optional)

MK-101-24HD   

PRODUCT SPECIFICATION

(A)  

Open the stand and place on 

flat surface   

(B)  

Remove Water Basin, 

place saw on stand   

(C)  

Ensure the back of the 

saw frame is positioned 

properly

(E)  

Reinstall the Water Basin

(D)  

The front of the saw 

frame will extend 7” in 

front of the stand

If using the MK Diamond Stand, Part # 168244, follow these steps.

Summary of Contents for MK-101-24HD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands