MK Diamond Products MK-101-24HD Owner'S Manual & Operating Instructions Download Page 41

Page: 41 / 60

The MK-101-24HD is designed with power transmission Micro-V Belt. In order to ensure the MK-101-

24HD operates a peak efficiency, the Micro-V Belt should be inspected monthly, and changed if the

Micro-V Belt shows damage and/or excessive wear.

Micro-V Belt Inspection, Adjustment and Replacement

When a new belt is installed, it should be inspected and re-tensioned after the first forty-

eight (48) hours of operation.

NOTE:

(A)

Remove the Diamond Blade

(B)

Remove the Cutting Head (See

Adjusting the Cutting Head)

(C)

Remove the two top Belt Guard

Bolts

(D)

Remove Belt Guard bottom bolt

(E)

Inspect the Micro-V Belt for cracks,

fraying, separation and wear. Go to

step H if replacement is required

(F)

Check belt for proper tension. If tension

correct, go to step Q (proper tension

should be 1/8-inch

deflection)

(G)

Loosen the two front motor

mounting bolts. If re-tensioning

only, go to step N

(H)

Loosen the two back motor

mounting bolts

(I)

Loosen the Motor Adjustment Strap

MK-101-24HD

MAINTENANCE

Summary of Contents for MK-101-24HD





























































Search results

Summary of Contents for MK-101-24HD

Reviews:

Brands by name

Popular brands

MK Diamond Products MK-101-24HD, Owner'S Manual & Operating Instructions

Search results

Summary of Contents for MK-101-24HD

Reviews:

Brands by name

Popular brands