MK Diamond Products HD-101R Pro24 JCS Owner'S Manual Download Page 34

Page: 34 / 64

Hold the Post when removing the Retaining Bolts.

(A)

Ensure the ON/OFF Switch

is in the OFF position. Un-

plug the GFCI from the power

source.

(B)

Remove Water Basin and

Blade.

(C)

Remove the Cutting Head (See

Adjusting the Cutting Head.

(D)

Loosen the retaining bolts.

(E)

Remove the Standoffs and

retaining bolts together.

(F)

Relocate the Post to the rear

Post retaining holes.

(G)

Install and tighten with Standoffs

and retaining bolts.

(H)

Install the Cutting Head (See

Adjusting the Cutting Head.)

(I)

Install the Water Basin and

Blade.

CaUTion

HD-101R Pro24

aDJUSTMenT

aDJUSTinG THe PoST FoR MaXiMUM CUTTinG lenGTH

The Cutting Head and Post are heavy! Use care when changing the position of

the Cutting Head.

Summary of Contents for HD-101R Pro24 JCS

































































Search results

Summary of Contents for HD-101R Pro24 JCS

Reviews:

Related manuals for HD-101R Pro24 JCS

Brands by name

Popular brands

MK Diamond Products HD-101R Pro24 JCS, Owner'S Manual

Search results

Summary of Contents for HD-101R Pro24 JCS

Reviews:

Related manuals for HD-101R Pro24 JCS

Brands by name

Popular brands