MK Diamond Products HD-101R Pro24 JCS Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 64

background image

25

(A)

Place the Adjustable Cutting

Guide onto the Movable Cutting

Table Ruler/Stop and tighten

the retaining thumbscrew.

(A)

Install the retaining thumbscrew

through the washer and Splash

Guard then align to the hole found

on back of the Blade Guard.

(B)

Install the Splash Guard

onto the Blade Guard.

(A)

Install Water Pump

Discharge Fitting.

(B)

Press one end of the Cooling

Transfer Tube onto the Water

Pump Discharge Fitting.

(C)

Slide Cooling Flow Adjusting

Clamp onto the Cooling

Transfer Tube.

HD-101R Pro24

aSSeMBlY

adjustable Cutting Guide installation

Splash Guard installation

water Pump installation

noTe: The Adjustable Cutting Guide can be used on either side of the Diamond Blade.

«
...
23
24
25
26
27
...
»

Summary of Contents for HD-101R Pro24 JCS

































































Reviews:

No comments

Related manuals for HD-101R Pro24 JCS

CS 65/1500 PLUS

Brand: F.F. Group Pages: 56

Brand: Pattfield Ergo Tools Pages: 92

Brand: Stihl Pages: 40

Brand: KRAFTtech Pages: 23

Brand: HART Pages: 24

Brand: Feider Machines Pages: 14

Brand: EarthWise Pages: 48

KSP 40 Flexistem

Brand: Mafell Pages: 15

Brand: Milwaukee Pages: 2

Brand: Draper Pages: 12

Brand: Draper Pages: 20

Brand: Hyd-Mech Pages: 80

Brand: Scheppach Pages: 60

Brand: EINHELL Bavaria Pages: 34

Brand: EINHELL Pages: 88

Brand: EINHELL Pages: 180

Brand: EINHELL Pages: 76

Brand: EINHELL Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands