Mitsubishi MOTORS OUTLANDER PHEV 2019 Quick Manual Download

Page: 5 / 10

Warning!

While driving, do not put any object near the selector lever, which may be accidentally pushed against the selector, which may then

move into .

Around the Selector Lever

NORMAL

Function

Drive mode

SNOW

LOCK

This mode can be used on both dry and wet roads. The distribution of driving/braking

torque to each wheel is automatically controlled according to the driving condition.

This mode is for driving where maximum traction is required. This mode is suitable

for driving on rough roads or driving in sand or fresh snow.

This mode is for driving on slippery road surfaces, such as snow-covered roads and

improves stability on a slippery road.

SPORT mode switch

Pressing the switch while the READY indicator is on, you can switch the SPORT mode.This mode

enables quick acceleration in response to operation of the accelerator pedal and quick deceleration by

strong regenerative braking force. To cancel the SPORT mode, press the switch again or put the

operation mode in OFF.

Drive mode switch

Operating the switch with the operation mode in ON, you can change the S-AWC drive mode.

EV Switch

Pressing the switch with the operation mode in ON, you can drive the vehicle by using only the EV drive

mode as much as possible, even if the accelerator pedal is roughly depressed. (EV priority mode)

This mode helps drive the vehicle at a place needed for concern of noises and exhaust gas emissions,

such as residential areas etc.

Selector Lever

R (Reverse)

N (Neutral)

: No drive is transmitted to the wheels, which are not locked either.

D (Drive)

B (Regenerative brake)

: The vehicle moves in reverse.

: The vehicle moves forward.

: The intensity of regenerative brake increases.

• Select position you chose is illuminated on the panel behind the selector lever and in the meter.

• Only when the select position is “ ” position, you can shift to the “ (Regenerative brake)” position.

• When “ ” position is selected and large regenerative braking force is applied, the brake lamps will

automatically illuminate.

SAVE/CHARGE mode switch

Electric Parking Brake Switch

Pull up the switch while depressing the brake pedal to apply the parking brake. The indicator lamp on

the switch will come on.

Press the switch while depressing the brake pedal to release the parking brake.

Brake Auto Hold Switch

Pressing the switch while all of the following conditions are met, the brake auto hold system will change

to the standby state and the indicator lamp on the switch comes on.

• The operation mode of the power switch in ON.

• The driver’s seat belt is fastened.

• The driver’s door is closed.

When the vehicle is stopped by depressing the brake pedal with the select position in any position other

than “ ” (PARK) or “ ” (REVERSE), the system activates and the vehicle can be held stationary

even if you release your foot from the brake pedal.

The brake auto hold indicator lamp in the instrument cluster will come on while the system activates.

When the accelerator pedal is depressed, the brakes are released.

Press the switch to lock the wheels when you are parking your vehicle. The indicator lamp on the

switch illuminates in green.

Electrical Parking Switch

Battery save mode

Pressing the switch with the operation mode in ON, you can change the drive battery mode in the

order of SAVE, CHARGE, OFF, SAVE.

To save the remaining power in the drive battery while driving, the battery save mode

can be used.

When the battery save mode is activated, the engine will start in order to

preserve the remaining

power of the drive battery and the vehicle will operate in the series hybrid mode or the parallel hybrid

mode depending on the remaining power in the drive battery.

Battery charge mode

To charge the drive battery while driving, the battery charge mode can be used.

When the battery

charge mode is activated, the engine will start to charge the drive battery to nearly full.

Even if the S-AWC drive mode is selected,after turning the operation mode of the power switch OFF

and turning to ON again,the S-AWC drive mode is set to “NORMAL”.

01 SPORT mode switch

Pressing the switch while the READY indicator is on, you can
switch the SPORT mode. This mode enables quick acceleration
in response to operation of the accelerator pedal and quick
deceleration by strong regenerative braking force. To cancel
the SPORT mode, press the switch again or put the operation
mode in OFF.

02 Drive mode switch

Operating the switch with the operation mode in ON, you can
change the S-AWC drive mode.

Drive mode

Function

NORMAL

This mode can be used on both dry and wet
roads. The distribution of driving/braking
torque to each wheel is automatically controlled
according to the driving condition.

SNOW

This mode is for driving on slippery road
surfaces, such as snow-covered roads and
improves stability on a slippery road.

LOCK

This mode is for driving where maximum
traction is required. This mode is suitable for
driving on rough roads or driving in sand or fresh
snow.

Even if the S-AWC drive mode is selected, after turning the
operation mode of the power switch OFF and turning to ON again,
the S-AWC drive mode is set to “NORMAL”.

03 EV Switch

Pressing the switch with the operation mode in ON, you can
drive the vehicle by using only the EV drive mode as much as
possible, even if the accelerator pedal is roughly depressed.
(EV priority mode)

04 SAVE/CHARGE mode switch

Pressing the switch with the operation mode in ON, you can
change the drive battery mode in the order of SAVE, CHARGE,
OFF, SAVE.

Battery save mode

To save the remaining power in the drive battery while driving, the
battery save mode can be used.

When the battery save mode is activated, the engine will start in
order to preserve the remaining power of the drive battery and
the vehicle will operate in the series hybrid mode or the parallel
hybrid mode depending on the remaining power in the drive
battery.

Battery charge mode

To charge the drive battery while driving, the battery charge
mode can be used. When the battery charge mode is activated,
the engine will start to charge the drive battery to nearly full.

05 Selector Lever

R (Reverse) :

The vehicle moves in reverse.

N (Neutral) :

No drive is transmitted to

the wheels, which are not locked

either.

D (Drive) :

The vehicle moves forward.

B (Regenerative brake) : The intensity of regenerative brake

increases.

• Select position you chose is illuminated on the panel behind the

selector lever and in the meter.

• Only when the select position is “ ” position, you can shift to the

“ (Regenerative brake)” position.

• When “ ” position is selected and large regenerative braking

force is applied, the brake lamps will automatically illuminate.

06 Electrical Parking Switch

Press the switch to lock the wheels when you are parking your
vehicle. The indicator lamp on the switch illuminates in green.

07 Electric Parking Brake Switch

Pull up the switch while depressing the brake pedal to apply the
parking brake. The indicator lamp on the switch will come on.

Press the switch while depressing the brake pedal to release the
parking brake.

08 Brake Auto Hold Switch

Pressing the switch while all of the following conditions are met,
the brake auto hold system will change to the standby state and
the indicator lamp on the switch comes on.

  • The operation mode of the power switch in ON.
  • The driver’s seat belt is fastened.
  • The driver’s door is closed.

When the vehicle is stopped by depressing the brake pedal
with the select position in any position other than “ ” (PARK) or
“ ” (REVERSE), the system activates and the vehicle can be held
stationary even if you release your foot from the brake pedal.

The brake auto hold indicator lamp in the instrument cluster will
come on while the system activates.

When the accelerator pedal is depressed, the brakes are released.