Mitsubishi Electric PUHZ-W112VHA Service Manual Download Page 56

Page: 56 / 58

OPERATING PROCEDURE

PHOTOS/FIGURES

13. Removing the compressor (MC)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the cover panel (front).

(4) Remove the electrical parts box. (See Photo 4)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7) Remove the side panel (R).

(8) Remove 2 screws (separator side/4 × 10) and 4 screws

(M/S and base side/5 × 12) to remove the front panel.

(9) Remove 3 separator fixing screws (4 × 10) and remove

the separator.

(10) Remove the soundproof cover for compressor.

(11) Remove the terminal cover and remove the compressor

lead wire.

(12) Recover refrigerant.

(13) Remove the 3 points of the compressor fixing nut using a

spanner or a adjustable wrench.

(14) Remove the welded pipe of compressor inlet and outlet

then remove the compressor.

Note: Recover refrigerant without spreading it in the air.

Photo 14

14. Removing the power receiver

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the cover panel (front).

(4) Remove the electrical parts box. (See Photo 4)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7) Remove the side panel (R).

(8) Recover refrigerant.

(9)

Remove 4 welded pipes of power receiver inlet and outlet.

(10) Remove 2 receiver leg fixing screws (4 × 10).

Note: Recover refrigerant without spreading it in the air.

Pipes of power receiver

Compressor (MC)

Terminal cover

Compressor

fi xing nut

Plate heat exchanger

fi xing screw

Receiver leg

fi xing screw

Power

receiver

HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Issued: Apr. 2019 No. OCH562 REVISED EDITION-D

Issued: Dec. 2017 No. OCH562 REVISED EDITION-C

Issued: Jul. 2015 No. OCH562 REVISED EDITION-B

Issued: Nov. 2014 No. OCH562 REVISED EDITION-A

Published: Jun. 2014 No. OCH562

Made in Japan

Specifications are subject to change without notice.

Summary of Contents for PUHZ-W112VHA



























































Search results

Summary of Contents for PUHZ-W112VHA

Reviews:

Brands by name

Popular brands

Mitsubishi Electric PUHZ-W112VHA, Service Manual

Search results

Summary of Contents for PUHZ-W112VHA

Reviews:

Brands by name

Popular brands