Mitsubishi Electric PUHZ-W112VHA Service Manual Download Page 55

Page: 55 / 58

OPERATING PROCEDURE

PHOTOS/FIGURES

11. Removing high pressure sensor (63HS)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 4)

(4) Recover refrigerant.

(5) Remove the welded part of high pressure sensor.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The welded part can be removed easily by remov-

ing the side panel (R).

Note 3: When installing the high pressure sensor, make

sure to cover it with a wet cloth to prevent it from

heating (100˚C or more), then braze the pipes so

that the inside of pipes are not oxidized.

Photo 12

12. Removing the plate heat exchanger

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the cover panel (front).

(4) Remove the electrical parts box. (See Photo 4)

(5) Remove the stay.

(6) Remove the water pipes connected to water outlet and

water inlet.

(7) Remove the side panel (R).

(8) Recover the refrigerant

(9) Remove 2 welded pipes of plate heat exchanger inlet

and outlet.

(10) Remove 3 plate heat exchanger fixing screws (4 × 10),

then remove the plate heat exchanger.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: Before removing the thermistor <Inlet water>

(TH32), recover water in the plate heat exchanger.

Photo 13

Plate heat

exchanger

Plate heat exchanger

fixing screw

Heat exchanger

Plate heat exchanger

fixing screws

Low pressure switch (63L)

High pressure sensor (63HS)

OCH562D

Summary of Contents for PUHZ-W112VHA



























































Search results

Summary of Contents for PUHZ-W112VHA

Reviews:

Brands by name

Popular brands

Mitsubishi Electric PUHZ-W112VHA, Service Manual

Search results

Summary of Contents for PUHZ-W112VHA

Reviews:

Brands by name

Popular brands