23
OCH562D
Check Code Abnormal point and detection method
Cause
Judgment and action
E0
or
E
Remote controller transmission error
(E0)/signal receiving error (E4)
1
Abnormal if main or sub remote
controller cannot receive any
transmission normally from Interface
unit/Flow temp. controller of refrigerant
address “0” for 3 minutes.
(Check code: E0)
2
Abnormal if sub-remote controller could
not receive any signal for 2 minutes.
(Check code: E0)
1
Abnormal if Interface/Flow temp.
controller board cannot receive any data
normally from remote controller board
or from other Interface/Flow temp.
controller board for 3 minutes.
(Check code: E4)
2
Interface/Flow temp. controller board
cannot receive any signal from remote
controller for 2 minutes.
(Check code: E4)
1
Contact failure at transmission
wire of remote controller
2
All remote controllers are set
as “sub” remote controller.
In this case, E0 is displayed
on remote controller, and E4
is displayed at LED (LED1,
LED2) on the outdoor control-
ler circuit board.
3
Miswiring of remote controller
4
Defective transmitting receiv-
ing circuit of remote controller
5
Noise has entered into the
transmission wire of remote
controller.
1
Check disconnection or looseness of
Interface unit/Flow temp. controller unit or
transmission wire of remote controller.
2
Set one of the remote controllers “main”, if
there is no problem with the action above.
3
Check wiring of remote controller.
• Total wiring length: max. 500 m
(Do not use cable × 3 or more.)
• The number of connecting remote controller:
Refer to the indoor units service manual.
If the cause of trouble is not in
1
–
3
above,
4
Diagnose remote controllers.
a) When “RC OK” is displayed, remote
controllers have no problem.
Turn the power off, and on again to check.
If abnormality occurs again, replace
Interface/Flow temp. controller board.
b) When “RC NG” is displayed, replace
remote controller.
c) When “RC E3” or “ERC 00-66” is displayed,
noise may be causing abnormality.
E1
or
E2
Remote controller control board
1
Abnormal if data cannot be read normally
from the nonvolatile memory of the remote
controller control board.(Check code: E1)
2
Abnormal if the clock function of remote
controller cannot be operated normally.
(Check code: E2)
1
Defective remote controller
1
Replace remote controller.
E3
or
E5
Remote controller transmission error
(E3)/signal receiving error (E5)
1
Abnormal if remote controller could not
find blank of transmission path for 6 sec-
onds and could not transmit.
(Check code: E3)
2
When remote controller receives the
transmitted data same time and com-
pares these data. Abnormal if the data is
judged to be different for 30 continuous
times. (Check code: E3)
1
Abnormal if Interface/Flow temp. control-
ler board could not find blank of transmis-
sion path. (Check code: E5)
2
When Interface/Flow temp. controller
receives the transmitted data same time
and compares these data. Abnormal if
the data is judged to be different for 30
continuous times. (Check code: E5)
1
2 remote controllers are set as
“main.”
(In case of 2 remote control-
lers)
Note that some models can
only connect 1 remote con-
troller. For more detail, refer
to the indoor unit's service
manual.
2
Defective transmitting receiv-
ing circuit of remote controller
3
Defective transmitting receiv-
ing circuit of Interface/Flow
temp. controller board
4
Noise has entered into trans-
mission wire of remote con-
troller.
1
Set a remote controller to main, and the
other to sub.
2
–
4
Diagnose remote controller.
a) When “RC OK” is displayed, remote
controllers have no problem.
Turn the power off, and on again to
check.
When becoming abnormal again, replace
indoor controller board.
b) When “RC NG” is displayed, replace
remote controller.
c) When “RC E3” or “ERC 00-66” is
displayed, noise may be causing
abnormality.
E6
Interface unit/Flow temp. controller-out-
door unit communication error (Signal
receiving error)
1
Abnormal if Interface/Flow temp.
controller board cannot receive any
signal normally for 6 minutes after
turning the power on.
2
Abnormal if Interface/Flow temp.
controller board cannot receive any
signal normally for 3 minutes.
1
Contact failure, short circuit or,
miswiring (converse wiring) of
Interface unit/Flow temp. control-
ler-outdoor unit connecting wire
2
Defective transmitting receiving circuit of
Interface/Flow temp. controller board
3
Defective transmitting receiv-
ing circuit of Interface/Flow
temp. controller board
4
Noise has entered into Interface
unit/Flow temp. controller-
outdoor unit connecting wire.
Note: Check LED display on the outdoor control
circuit board. (Connect A-control service
tool, PAC-SK52ST.)
1
Check disconnection or looseness of
Interface unit/Flow temp. controller-outdoor
unit connecting wire of Interface unit/Flow
temp. controller or outdoor unit.
2
–
4
Turn the power off, and on again to
check. If abnormality occurs again,
replace Interface/Flow temp. controller
board or outdoor controller circuit board.
E8
Interface unit/Flow temp. controller-
outdoor unit communication error
(Signal receiving error)
(Outdoor unit)
(1) Abnormal if outdoor controller circuit
board could not receive anything
normally for 3 minutes.
1
Contact failure of Interface
unit/Flow temp. controller-
outdoor unit connecting wire
2
Defective communication circuit
of outdoor controller circuit board
3
Defective communication
circuit of Interface/Flow temp.
controller board
4
Noise has entered into
Interface unit/Flow temp.
controller-outdoor unit
connecting wire.
1
Check disconnection or looseness of
Interface unit/Flow temp. controller-outdoor
unit connecting wire of Interface unit/Flow
temp. controller or outdoor unit.
2
–
4
Turn the power off, and on again to
check. Replace Interface/Flow temp.
controller board or outdoor controller circuit
board if abnormality is displayed again.
Summary of Contents for PUHZ-W112VHA
Page 58: ......
