9
Each air conditioner has its own refrigerant address No. and unit No.
(Example below).
To fi nd air conditioner No. to set, refer to the procedures below.
Air conditioner No. is found by its airflow direction with the unit No.
changed one after the other.
How to fi nd air conditioner No.
Check from refrigerant address 00 at first.
Change to unit No.1 and check
Change to unit No.2 and check
Change to unit No.3 and check
Change to unit No.4 and check
Change to unit No.1 and check
Change to unit No.2 and check
Change to unit No.3 and check
Change to unit No.4 and check
Change to unit No.1 and check
Change to unit No.2 and check
Change to unit No.3 and check
Change to unit No.4 and check
Change to unit No.1 and check
Change to unit No.2 and check
Change to unit No.3 and check
Change to unit No.4 and check
When "Err" is displayed, refrigerant address
does not heve further "unit No.".
Change to the next "refrigerant address No..
(Refrigerant No "00"~max. No."15")
<Process to fi nd air conditioner No.>
[1] To check refrigerant address No. and unit No.
1.Press Mode button (Return button) and unit No. or refrigerant
address No. blinks.
Adjust refrigerant address No.to "00" and unit No."1" with Set
Temperature button .
2.Press Filter button to send the information on remote controller.
3. Wait for 15 seconds . How does the air conditioner run?
Only air from the outlet which No. displayed on remote controller
blows downward.
Refrigerant address No.00 and unit No.1 are the air conditioner No..
All outlets are closed.
Go to step [2].
[2] To check by changing unit No. one after the other
(Maximum unit No. is 4)
1.Press Mode button (Return button) and unit No. blinks.
[3] To check Unit No. of following refrigerant address No.(Maxmum
refrigerant address No. is 15)
1.Press Mode button (Return button) to blink refrigerant address No..
Adjust refrigerant No. with Set Temperature button .
* By changing refrigerant address, unit No. and outlet No. turn to initial
display.
2.Go back to [2] and check Unit No. again from Unit No. 1 in order.
To clear fi xed setting
To clear all fi xed setting(reset to factory default), press check button(clear
botton) for more than 3 seconds in fi xed airfl ow direction mode.
Display of remote controller blinks and the set information is cleared.
Note:
This operation clears the fixed setting information of all air
conditioner connected to the remote controller.
Outlet No. Up/Down air direction
Refrigerant addres No.
Unit No.
Outlet No.
Up/Down air direction Refrigerant addres No.
Unit No.
Err
Outlet No.
Up/Down air direction Refrigerant addres No.
Unit No.
Adjust to the next unit No.with Set Temperature button .
(refrigerant address No.00 is remained.)
2. Press Filter button to send the information on remote controller.
3. Wait for 15 seconds . How does the air conditioner run?
Only air from the outlet which No. displayed on remote controller blows
downward.
No. displayed in remote controller is air conditioner No. (Checking
completed)
All outlets are closed.
Repeat [1] and check. (If all the numbers are checked up to No.4
and is not found, go to [3].)
"Err" is displayed on remote controller.
The refrigerant address does not have further unit No.. (Go to [3].)
5.6. Ventillation
For LOSSNAY combination
5.6.1. For Wired Remote-controller
To run the ventilator together with the indoor unit:
Press the ON/OFF button .
•
The Vent indication appears on the screen (at
8
). The ventilator
will now automatically operate whenever the indoor unit is run-
ning.
To run the ventilator independently:
Press the Mode button until
appears on the display. This
will cause the ventilatoPr to start.
To change the ventilator force:
Press the Ventilation button as necessary.
•
Each press toggles the setting, as shown below.
5.6.2. For Wireless Remote-controller
The ventillator will automatically operate when the indoor unit turns on.
No indication on the wireless remote controller.
High
Low
5. Operation
Refrigerant
address
No.”00”
Refrigerant
address
No.”01”
Unit No.”1”
Unit No.”2”
Unit No.”1”
Unit No.”2”
As for this air conditioner,
air conditioner No. is “Unit No.1”
of refrigerant address “0”.
Remote controller
01̲RG79D307H01̲EN̲070524.indd 9
01̲RG79D307H01̲EN̲070524.indd 9
2007/05/24 16:39:46
2007/05/24 16:39:46
