Mitsubishi Electric PAC-SIF051B-E Installation Manual Download Page 6

Page: 6 / 64

3. System

3.3 Third step (Functions setting)

DHW tank Immersion

heater

Booster

heater

function

System diagram

Thermistor

Reference

section

Remarks

Present

Absent

Present

For heating

and DHW

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

Present

For heating

and DHW

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

Present

Absent

Present

For heating

only

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

1. ‘Legionella

Prevention

Mode’ cannot

be selected in

this system.

Present

Absent

—

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

1. ‘Legionella

Prevention

Mode’ cannot

be selected in

this system.

2. Please make

sure water cir-

cuit not to get

frozen during

defrost.

Present

For heating

only

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

Present

Absent

—

THW1: Flow water temp.

THW2: Return water temp.

THW5B: Tank water temp.

4.4

4.5

5.3

Absent

Present

—

THW1: Flow water temp.

THW2: Return water temp.

4.4

4.5

5.3

Absent

—

THW1: Flow water temp.

THW2: Return water temp.

4.4

4.5

5.3

1. Please make

sure water cir-

cuit not to get

frozen during

defrost.

* The use of two 2-way valves can perform same function as a 3-way valve.

Booster heater

Heat emitter

DHW tank

THW5B

THW1

THW2

3-way valve (

)

Booster heater

Heat emitter

DHW tank

THW5B

THW1

THW2

Immersion heater

3-way valve (

)

Heat emitter

DHW tank

THW5B

THW1

THW2

3-way valve (

)

Booster heater

Heat emitter

THW1

THW2

Heat emitter

THW1

THW2

Heat emitter

DHW tank

THW5B

THW1

THW2

Immersion heater

3-way valve (

)

Booster heater

Heat emitter

DHW tank

THW5B

THW1

THW2

3-way valve (

)

Booster heater

Heat emitter

DHW tank

THW5B

THW1

THW2

Immersion heater

3-way valve (

)

Summary of Contents for PAC-SIF051B-E

































































Search results

Summary of Contents for PAC-SIF051B-E

Reviews:

Related manuals for PAC-SIF051B-E

Brands by name

Popular brands

Mitsubishi Electric PAC-SIF051B-E, Installation Manual

Search results

Summary of Contents for PAC-SIF051B-E

Reviews:

Related manuals for PAC-SIF051B-E

Brands by name

Popular brands