background image

11

S1

S2

S3

L

N

L

N

BLACK

BLACK

YELLOW

YELLOW

YELLOW

YELLOW

BLACK

BLACK

CNO1

CNO1

CNO1

Black

CNO1

Black

FTC

(Main)

FTC

(Main)

S1

S2

S3

Initial settings

(Power supplied 

by outdoor unit)

Modified settings

(Separate power 

supply to 

FTC(Main))

Power

supply

~/N

230V

50Hz

Earth

leakage

breaker

*1

*1

*1

*1

Wiring

circuit

breaker

or

Isolating

switch

L

N

S1
S2
S3

Outdoor unit

S1
S2
S3

TB2

TB1

L

N

ECB

Wiring

circuit

breaker

or

Isolating

switch

To control 

board

ELB for

immersion

heater

(DHW tank)

L
N

Power

supply

~/N

230V

50Hz

Earth

leakage

breaker

Wiring

circuit

breaker

or

Isolating

switch

Power

supply

circuit

circuit

: PAC-IF071B-E

: PAC-IF072/073B-E

FTC (Main)

Power

supply

3N~

400V

50Hz

Earth

leakage

breaker

Wiring

circuit

breaker

or

Isolating

switch

L3

L2

L1

N

S1
S2
S3

Outdoor unit

S1
S2
S3

TB2

TB1

L

N

ECB

Wiring

circuit

breaker

or

Isolating

switch

To control 

board

ELB for

immersion

heater

(DHW tank)

L
N

Power

supply

~/N

230V

50Hz

Earth

leakage

breaker

Wiring

circuit

breaker

or

Isolating

switch

circuit

circuit

FTC (Main)

~/N

230V

50Hz

Power

supply

~/N

230V

50Hz

en  

4.  Electrical work

Option 2: FTC (Main) powered by independent source

If FTC (Main) and outdoor units have separate power supplies, the following re-

quirements MUST be carried out:

• FTC (Main) unit electrical box connector connections changed. (see Fig. 

4.1.3)

• Outdoor unit DIP switch settings changed to SW8-3 ON.

• Turn on the outdoor unit before the FTC (Main).

• Power by independent source is not available for particular models of 

outdoor unit model.

For more detail, refer to the connecting outdoor unit installation manual.

<Fig.  4.1.3>

<Fig.  4.1.5>

Electrical connections 1 phase/3 phase

FTC (Main) power supply

~/N 230 V  50 Hz

FTC (Main) input capacity

Main switch (Breaker)

*1

16 A

Wiring

Wiring No. × size (mm²)

FTC (Main) power supply

2 × Min. 1.5

FTC (Main) power supply earth

1 × Min. 1.5

FTC (Main) - Outdoor unit

*2

2 × Min. 0.3

FTC (Main) - Outdoor unit earth

Circuit  rating

FTC (Main) L - N

*3

230V AC

FTC (Main) - Outdoor unit S1 - S2

*3

FTC (Main) - Outdoor unit S2 - S3

*3

24V DC

*2.  Max. 120 m

*3.   The values given in the table above are not always measured against the 

ground value.

Notes: 1. Wiring size must comply with the applicable local and national codes.

2. 

FTC (Main) unit/outdoor unit connecting cords shall not be lighter 

than polychloroprene sheathed flexible cord. (Design 60245 IEC 57)

FTC (Main) unit power supply cords shall not be lighter than 

polychloroprene sheathed flexible cord. (Design 60227 IEC 53)

3. Install an earth longer than other cables.

4. Please keep enough output capacity of power supply for each individual 

heater. Insufficient power supply capacity might cause chattering.

TB2

Clamps

Slot

TB1

Clamps

1

2

3 4

5

Notes: 1.  Do not run the low voltage cables through a slot that the high voltage cables go through.

2.  Do not run other cables except low voltage cables through a slot that the wireless receiver’s cable goes through.

3.  Do not bundle power cables together with other cables.

4.  Bundle cables as figure above by using clamps.

*1.   If the installed earth leakage circuit breaker does not have an over-current protection function, install a breaker with that function along the same power line.

 A breaker with at least 3.0 mm contact separation in each pole shall be provided. Use earth leakage breaker (NV).

The breaker shall be provided to ensure disconnection of all active phase conductors of the supply.

Note:  In accordance with IEE regulations the circuit breaker/isolating switch located on the outdoor unit should be installed with lockable devices (health and safety).

<Fig. 4.1.4>  Wiring for PAC-IF07*B-E

1

High voltage cables (OUTPUT)

2

High voltage cables (OUTPUT)

3

Low voltage cables (INPUT) and 

wireless receiver’s cable

4

Thermistor cables

5

Power cables

Clamps

Clamps

<3 phase>

<1 phase>

Summary of Contents for PAC-SIF051B-E

































































Reviews: