9
Movement of the horizontal vane
NOTE:
• Adjust the AIR FLOW direction using the remote controller. Moving the horizontal vane and vertical vane
manually can cause trouble.
• When the operation mode changes in “
(AUTO)” mode, the horizontal vane is automatically changed
to the position in each mode.
COOL/DRY
HEAT
• The vane automatically moves to horizontal position.
It will not swing.
NOTE:
Air blows out upper than position (1).
• To constantly change the air flow direction, select
(SWING) with the
VANE
button.
Horizontal position
At the start
of heating
operation
Horizontal
position
Very small
air flow
When air
becomes
warm...
Position (4)
• Immediately after the air conditioner starts operating,
the vane stays at horizontal position. Once the air from
the indoor unit becomes sufficiently warm, the vane
moves to position (4).
• Once the air conditioner starts operating, the fan speed
increases gradually as the air from the indoor unit gets
warmer, and continues until the set speed is finally reached.
After
around 0.5
to 1 hour
Position (1)
When the air flow direction is
set to position (2), (3) or (4)
• After around one hour of operation, the air conditioner
automatically moves the vane to position (1).
To change the air flow direction to the original setting,
operate the VANE button on the remote controller again.
• The vane does not move to the straight-down
position in the COOL and DRY mode.
At the start
of heating
operation
Horizontal
position
Very small
air flow
When air
becomes
warm...
Set position
• Immediately after the air conditioner starts operating,
the vane stays at horizontal position. Once the air
from the indoor unit becomes sufficiently warm,
the vane moves to the position corresponding to the
set direction of air flow.
• Once the air conditioner starts operating, the fan
speed increases gradually as the air from the indoor
unit gets warmer, and continues until the set speed
is finally reached.
• The vane moves intermittently between positions (1)
and (4). The vane stops for a brief period at positions
(1) and (4).
• The vane moves intermittently between positions (2) and (4).
The vane stops for a brief period at positions (2) and (4).
AUT
O
MAUAL
SWING
HEAT
COOL
DRY
■
To change the AIR FLOW velocity, press the
FAN
button.
Each time the button is pressed, the fan speed is changed in sequence:
(Low)
→
(Med.)
→
(High)
→
(Supper High)
→
(AUTO)
• Use the
(Super High) notch to cool/heat the room more efficiently.
• If the operating sound of the air conditioner disturbs your sleep, use the
(Low) notch.
■
To change the AIR FLOW blowing direction vertically, press the
VANE
button.
Each time the button is pressed, the angle of the horizontal vane is changed in
sequence: (1)
→
(2)
→
(3)
→
(4)
→
(SWING)
→
(AUTO)
SWING OPERATION
Use the swing operation for the air flow to reach all corners of the room.
Recommended horizontal vane range for more
efficient air-conditioning
Use the (AUTO) position usually.
Use position
(1) in the COOL or DRY mode and
use positions (2) to (4) in the HEAT mode when
adjusting to your requirements.
AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT
AIR FLOW velocity and direction can be selected as required.
To air-condition mainly the
left area of the room
To air-condition the entire room The
horizontal air flow direction and indoor unit
display are switched according to the room
temperature (floor/wall).
To air-condition mainly the
right area of the room
Remote controller button
Press
to select LEFT.
Press
to select AUTO.
Press
to select RIGHT.
Remote controller display
i-see Sensor operation
Control range
of horizontal air
flow direction.
The vertical air
flow direction
conforms to the
setting on the re-
mote controller.
(The horizontal
air flow direction
is controlled in
this range. )
Installed
at center
Installed
at left
Installed
at right
Indoor unit
display
AREA
AREA SETTING
