5
PREPARATION BEFORE OPERATION
Handling of the remote controller
•
The range that the signal can reach is about 6 m when
the remote controller is pointed at the front of the
indoor unit.
•
When a button is pressed, one or two beeps will be
heard from the indoor unit. If no sound is heard, operate
again.
•
Use the remote controller carefully.
If it is dropped, thrown or it gets wet, the remote controller
may not operate.
•
Since the display on the remote controller is made of
liq uid crystal (glass), it may not light up if it is damaged
from falling.
•
Refer to page 1 0 when the indoor unit does not respond
to the remote control signal.
When installing on a wall, etc.
•
Install the remote controller holder in a position where
the signal reception sound (beep) can be heard from
the indoor unit when the
ON/OFF
button is pressed.
How to install/remove the remote controller
Installing : Insert the remote controller downward.
Removing : Pull it up.
Dry-cell batteries
Reference for replacing batteries
Replace the batteries with new AAA alk aline batteries
in the following cases:
·
When the indoor unit does not respond to the remote
control signal.
·
When the display on the remote controller becomes dim.
·
When a button of the remote controller is pressed, all
displays appear on the screen, and then disappear
immediately.
Do not use manganese batteries. The remote controller
could malfunction.
•
The service life of an alk aline battery is about 1 year.
However, a battery whose time limit is approaching
may be ex hausted soon. The recommended usable
time limit is indicated (month/year) on the bottom of
the battery.
•
To prevent liq uid leak age, tak e out all batteries when
the remote controller is not going to be used for a
long time.
CAUTION:
If liquid from the batteries gets onto your skin or
clothes, wash it well with clean water.
If liquid from the batteries gets into your eyes, wash
them well with clean water and consult a doctor at once.
•
Do not use rechargeable batteries.
•
Replace the 2 batteries with new ones of the same
type.
•
Dispose of ex hausted batteries in the correct manner.
Remote controller
holder
When the remote controller cannot be used (emergency operation)
When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation
can be done using the EMERGENCY OPERATION switch.
COOL & HEAT type
Press the EMERGENCY OPERATION switch.
• Each time the EMERGENCY OPERATION switch is
pressed, the unit will operate in order of EMER-
GENCY COOL MODE, EMERGENCY HEAT MODE
and STOP MODE.
However, when the EMERGENCY OPERATION
switch is once pressed, the unit will operate in test
run for 30 minutes and then the operation mode
shifts to EMERGENCY MODE.
• Details of EMERGENCY MODE are as shown below.
However, the temperature control does not work
for 30 minutes in test run and the unit is set to
continuous operation. The fan speed is set to High
in test run and shifts to Medium after 30 minutes.
Operation mode
COOL
HEAT
Set temperature
2 4
°
C
2 4
°
C
Fan speed
Medium
Medium
Horiz ontal vane
Auto
Auto
•
The operation mode is indicated by the Operation
Indicator lamp on the indoor unit as following
figure.
Operation Indicator lamp
To stop the emergency operation, press the
EMERGENCY OPERATION switch once (in
case of EMERGENCY HEAT MODE) or twice
(in case of EMERGENCY COOL MODE).
COOL ONLY type
Press the EMERGENCY OPERATION switch.
• When the EMERGENCY OPERATION switch is
pressed, the unit will operate in test run for 30
minutes at first and then the operation mode shifts
to EMERGENCY COOL MODE.
• Details of EMERGENCY COOL MODE are as shown
below. However, the temperature control does not
work for 30 minutes in test run and the unit is set to
continuous operation. The fan speed is set to High
in test run and shifts to Medium after 30 minutes.
Operation mode
COOL
Set temperature
2 4
°
C
Fan speed
Medium
Horiz ontal vane
Auto
•
The operation mode is indicated by the Operation
Indicator lamp on the indoor unit as following
figure.
Operation Indicator lamp
To stop the EMERGENCY COOL MODE, press
the EMERGENCY OPERATION switch again.
Each time the switch is pressed, the operation mode
alternates between the EMERG ENCY COOL MODE
and STOP MODE.
Operation Indicator
Operation Indicator
Operation Indicator
EMERG ENCY HEAT
EMERG ENCY COOL
STOP
Operation Indicator
Operation Indicator
EMERG ENCY COOL
STOP
ON/OFF
FAN
TOO
WARM
TOO
COOL
VANE
MODE
ECONO COOL
STOP
START
HR.
MIN.
I FEEL COOL
DRY
AMPM
CLOCK
˚
C
AMPM
RESET CLOCK
HEAT
/FAN
Remote controller
How to set the batteries and the current
time
Remove the front lid and insert batteries.
Then reattach the front lid.
Insert the minus pole of the batteries first.
Check if the polarity of the batteries is correct.
Press the RESET button.
•
If the RESET button is not pressed, the remote con-
troller may not operate correctly.
Press the CLOCK set button.
Press the
HR.
and
MIN.
buttons (TIME SET
buttons) to set the current time.
•
Each time the
HR.
button is pressed, the set time
increases by 1 hour, and each time the
MIN.
button
is pressed, the set time increases by 1 minute.
Press the CLOCK set button again and close
the front lid.
Press using a
thin stick .
Insert the minus pole
of the batteries first.
Press using a
thin stick .
