Mitsubishi Electric Mr. Slim PU-P100VKA Service Manual Download

Page: 70 / 111

OCH670

<Outdoor unit operation monitor function>

[When optional part ‘A-Control Service Tool (PAC-SK52ST)’ is connected to outdoor controller board (CNM)]

Digital indicator LED1 displays 2 digit number or code to inform operation condition and the meaning of check code by

controlling DIP SW2 on ‘A-Control Service Tool’.

Operation indicator SW2 : Indicator change of self diagnosis

SW2 setting

2 3 4 5 6

Display detail

Explanation for display

Unit

<Digital indicator LED1 working details>

(Be sure that the 1 to 6 in the SW2 are set to OFF.)

(1) Display when the power supply ON

When the power supply ON, blinking displays by turns.

Wait for 4 minutes at the longest.

(2) When the display lights (Normal operation)

Operation mode display.

2 3 4 5 6

(Initial setting)

SW2

1 second

interval

LED1

(Lighting)

Display

Operation Model

The tens digit : Operation mode

The ones digit : Relay output

O
C

Display

Compressor

Warming-up

Compressor

—

OFF / FAN

COOLING / DRY *

Display during error postponement

Postponement code is displayed when

compressor stops due to the work of

protection device.

Postponement code is displayed while

error is being postponed.

*C5 is displayed during replacement operation.

(3) When the display blinks

Inspection code is displayed when compressor stops due to the work of protection devices.

Display Contents to be inspected (When power is turned on)

E0~E7

63H connector(yellow) is open.

Indoor/outdoor communication error (Signal receiving error) (Outdoor unit)

Indoor/outdoor communication error (Transmitting error) (Outdoor unit)

Miswiring of indoor/outdoor unit connecting wire, excessive number of indoor units (4 units or more)

Miswiring of indoor/outdoor unit connecting wire(converse wiring or disconnection)

Startup time over
Communication error except for outdoor unit

Display Inspection unit

0
1
2
3
4

Outdoor unit
Indoor unit 1
Indoor unit 2
Indoor unit 3
Indoor unit 4

Display

Contents to be inspected (During operation)

P1~P8

A0~A7

Abnormal high pressure (63H operated)

Abnormal high discharging temperature and comp. surface, shortage of refrigerant

Open/short circuit of discharge thermistor(TH4) and comp. surface thermistor(TH33)

Open/short of outdoor unit thermistors(TH6, TH7 and TH8)

Abnormal temperature of heatsink

Abnormality of power module

Abnormality of superheat due to low discharge temperature

Abnormality in outdoor fan motor

Overheat protection

Compressor overcurrent interruption (When Comp. locked)

Current sensor error

Abnormal low pressure

Compressor overcurrent interruption

Abnormality of refrigerant

Abnormality of indoor units

Communication error of M-NET system

Summary of Contents for Mr. Slim PU-P100VKA
















































































































Search results

Summary of Contents for Mr. Slim PU-P100VKA

Reviews:

Related manuals for Mr. Slim PU-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr. Slim PU-P100VKA, Service Manual

Search results

Summary of Contents for Mr. Slim PU-P100VKA

Reviews:

Related manuals for Mr. Slim PU-P100VKA

Brands by name

Popular brands