Mitsubishi Electric Mr. Slim PU-P100VKA Service Manual Download

Page: 59 / 111

OCH670

(4) Releasing emergency operation

Turn the main power supply off.

Set the emergency operation switch (SWE) on indoor controller board to OFF.

Set the shorting pins of emergency operation connector (CN31) on outdoor controller board to OFF.

Note:

If shorting pins are not set on emergency operation connector (CN31), the setting remains OFF.

9-8. EMERGENCY OPERATION

(1) When the check codes shown below are displayed on outdoor unit or microcomputer for wired remote controller or indoor

unit has a failure, but no other problems are found, emergency operation will be available by setting the emergency opera-

tion switch (SWE) on indoor controller board to ON and short-circuiting the connector (CN31) on outdoor controller board.

(2) Check the following items and cautions for emergency operation

Make sure that there is no abnormality in outdoor unit other than the above abnormalities. (Emergency operation will not

be available when check code other than the above are indicated.)

For emergency operation, it is necessary to set the emergency operation switch (SWE) on indoor controller board. Refer

to the electrical wiring diagram of indoor unit for how to set the indoor unit.

During emergency operation, the air-conditioner will continuously be operated by supplying power and stopping it: It can-

not be turned on or off by remote control, and temperature control is not possible.

Do not perform emergency heating operation for an extended period of time: If the outdoor unit starts defrosting during

this period, cold air will blow out from the indoor unit.

Do not perform emergency cooling operation for more than 10 hours: Neglecting this could result in freezing the heat

exchanger in indoor unit.

(3) Emergency operation procedure

Turn the main power supply off.

Turn on the emergency operation switch (SWE) on indoor controller board.

Set the shorting pins of emergency operation connector (CN31) on outdoor controller board to ON.

Turning the main power supply on will start the emergency operation.

OFF

CN31

Shorting pins

Inspected content
Open/short of outdoor unit thermistor (TH6/TH7/TH8)

Indoor/outdoor unit communication error • Signal receiving error (Outdoor unit)
Indoor/outdoor unit communication error • Transmitting error (Indoor unit)

Communication error other than outdoor unit

Communication error between outdoor controller board and M-NET board (Serial communication error)

Check code

E8
E9

E0 ~ E7

●

When following abnormalities occur, emergency operation will be available.

Summary of Contents for Mr. Slim PU-P100VKA
















































































































Search results

Summary of Contents for Mr. Slim PU-P100VKA

Reviews:

Related manuals for Mr. Slim PU-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr. Slim PU-P100VKA, Service Manual

Search results

Summary of Contents for Mr. Slim PU-P100VKA

Reviews:

Related manuals for Mr. Slim PU-P100VKA

Brands by name

Popular brands