Mitsubishi Electric MR-G50J, Operating Instructions Manual

Page: 19 / 32

19
To Stop the Operation Halfway through • To make ice again.
To Make Ice Fast (Quick ice making)
Press button to display the Ice
Making compartment.
Press button repeatedly.
When you want to stop making ice
to make
blink.
To start making ice again, make
or blink.
After a while, the indicator changes
from blinking to lighting and your
selection is set. A “beep” sound is heard.
page 9
MODE
SELECT
MODE
Remove the foods and ice in the
w a t e r t a n k a n d i c e m a k i n g
compartment.
Press button to display the Ice
Making compartment.
Press button and hold for about
3 seconds (until a “beep” sound is
heard.) Then the indicator blinks
and stays lit.
turns on after a while.
After about 1 minute later, clean the
w a t e r t a n k a n d i c e m a k i n g
compartment.
No cleaning will produce molding.
page 21
To use the Ice Making compartment as a refrigerator
Select the temperature mode to REF
when you don’t make ices in winter.
SELECT
●
When you want to start making ice, see above.
●
Temperature level display icon keeps
changing just right after selecting “REF” or
returning to the original position until the
temperature stabilizes.
Press button to display the Ice Making
compartment.
Press button repeatedly and make
blink.
After a while, the blinking display will stay lit.
Press button
The indicator turns on.
It automatically completes after operating for
about 9 hours, when the ice storage bin is full of
ice (about 60 to 100 pieces) or when no water is
left in the water tank.
light goes out and will stay lit.
MODE
QUICK
Note
●
The ice level sensor lever will detect the ice storage
automatically, and will stop ice-making when it reaches
a certain amount. (60 to 100pcs.)
(It is designed so that the ice will not become full in the
ice storage bin)
In order to detect the ice level correctly, please make
the ice flat and put the ice server in the front of the ice
storage bin.
Please do not pour anything like
sugar, juice or tea apart from water
in the water tank. (The water tank
can withstand up to 60˚C)
●
If you pour anything apart from
water into it, the water pump may become malfunction.
Do not fill the water tank higher than the filled-level
mark.
●
Filling the water tank with a kettle while it is still in the
tank holder, or filling it higher than the filled-level mark
may cause “connected” ice to form.
Please do not put
anything deep inside
the ice storage bin
Make the
ice flat
Ice storage bin
Door
Ice server
Ice level sensor lever
SELECT
●
The time for making ice varies with the room temperature
where this product is installed or conditions to use.
●
It might take 24 hours or more to make ice just after the
installation of the product.
Using Compar
tments
Ice Making Compar
tment
●
There may be white sediment (white crystal) or bubbles
inside the ice cube.
●
In cases below, may cause clear ice into such white
sediment ice.
•
When shifting from “Regular ice making mode” to “Crystal
ice making mode.” (Initial is set to “Regular ice making mode”)
•
Ice made of water containing much mineral. (This white
sediment is a crystal of mineral ingredients, making no harm.)
•
When surrounding temperature, status of use have changed.
•
When pieces of ice are stored long time in the ice storage bin.
(Frost will cover the ice. If it is put into water, the frost will dissolve.)
When you want to maintenance the clarity of the ice or the
ice making time Operation
page 25
About Crystal Ice
Ice making time
●
Approximately time for making one set of ice (5-8 pieces)
●
Ice making time can increase depending on the surrounding
temperature and the status of usage.
●
Please decrease the number of opening the door when
making clear ice.
Crystal Ice
making mode
6-9 hours
Clear ice is made slowly to increase the clarity of the ice cube.
Regular Ice
making mode
90-120 minutes
Quick ice
making mode
60-90 minutes
PU8>M;9=g9:59A6x>=
06.5.24, 6:33 PM 19