Mitsubishi Electric LY2-3300-B0B Instruction Manual Download Page 4

Page: 4 / 12

Lubrication

● Pour oil up to the arrow position before starting

operation.
　　　　…About 3 cc
　　　　…5, 6 drops
　　　　…1, 2 drops
For oil, use “Pulley SF oil” specified by
Mitsubishi.

※ Refer
Pulley SF oil ：Specific gravity (15℃ ) = 0.86 (g/cm

)

：Viscosity (40℃ ) = 18.0 (mm

/s)

● When a new sewing machine is used for the

first time, or sewing machine left out of use for
considerably long time is used again, replenish a
suitable amount of oil to the portions indicated
by arrows in the below figure.

Adjustment of lubrication to the

rotating hook

Adjust the lubrication amount of the rotating hook
by turning the screw Ⓐ.

USAGE PRECAUTION

Ⓐ

Screw Ⓐ

Decrease

Increase

Line

Hole for supply

Supply the oil to the tank of the bed

Fill oil up to the line when the oil would come
bottom level.

At ① and ②, please lubricate

the oil braid under the rubber plug.

②

①

— 1 —

Summary of Contents for LY2-3300-B0B













Search results

Summary of Contents for LY2-3300-B0B

Reviews:

Related manuals for LY2-3300-B0B

Brands by name

Popular brands

Mitsubishi Electric LY2-3300-B0B, Instruction Manual

Search results

Summary of Contents for LY2-3300-B0B

Reviews:

Related manuals for LY2-3300-B0B

Brands by name

Popular brands