Mitsubishi Electric LY2-3300-B0B Instruction Manual Download Page 11

Page: 11 / 12

LY2-3300-B0B Specifications

Model

Specifications

LY2-3300-B0B

Application

Heavy material

Max. sewing speed (rpm)

2,000

Stitch length (mm)

0 to 8

Needle bar stroke (mm)

35.0

Thread take-up lever stroke (mm)

73.0

Alternating movement (mm)

2.0 to 5.0 (feed foot)

Feed dog height (mm)

1.0

Presser foot stroke (mm)

Hand

6.0

Knee

13.0

Needle

DP × 17 #22 (DB × 1 #22)

Hook (vertical rotating hook)

Large

Lubrication system

Manual lubrication (The hook is supplied

with oil automatically from the tank)

Bed dimensions (mm)

475 ×178

Note: ● The bobbin should be of high quality free from deformation.

● Some materials and/or sewing conditions may require specifications other than those listed

above.

●These specifications are subject to change for machine improvement.

SPECIFICATIONS

— 8 —

Summary of Contents for LY2-3300-B0B













Search results

Summary of Contents for LY2-3300-B0B

Reviews:

Related manuals for LY2-3300-B0B

Brands by name

Popular brands

Mitsubishi Electric LY2-3300-B0B, Instruction Manual

Search results

Summary of Contents for LY2-3300-B0B

Reviews:

Related manuals for LY2-3300-B0B

Brands by name

Popular brands